Section
30 Pressure vessels/fired units/heat exchangers
30.1 Recognised codes and standards for pressure
vessels/fired units/heat exchangers/storage tanks
30.1.1 The following codes and standards are recognised by LR:
- API Std 510 Pressure Vessel Inspection Code
- API Std 530 Calculation of Heater Tube Thickness in Petroleum
Refineries
- API Std 620 Design and Construction of Large, Welded,
Low-Pressure Storage Tanks
- API Std 650 Welded Steel Tanks for Oil Storage
- API Std 660 Shell and Tube Heat Exchangers for General Refinery
Service
- API Std 661 Air Cooled Heat Exchangers for General Refinery
Service
- API Std 662, Part 1/ISO 15547-1 Plate Heat Exchangers for
General Refinery Services Plate-and-Frame Heat Exchangers
- API Std 668 Brazed Aluminum Plate-Fin Heat Exchangers
- ASME BPVC Sec I Boiler And Pressure Vessel Code, Section I,
Rules For The Construction Of Power Boilers
- ASME Section IV into ASME BPVC Sec IV Boiler and Pressure Vessel Code,
Section IV, Rules for Construction of Heating Boilers
- ASME BPVC Sec V Boiler And Pressure Vessel Code, Section V,
Nondestructive Examination
- ASME BPVC Sec VIII-1 Boiler And Pressure Vessel Code, Section
Viii, Rules For The Construction Of Pressure Vessels, Division 1
- ASME BPVC Sec VIII-2 Boiler And Pressure Vessel Code, Section
Viii, Rules For The Construction Of Pressure Vessels, Division 2
Alternative Rules
- ASME BPVC Sec VIII-3 Boiler And Pressure Vessel Code, Section
Viii, Rules For The Construction Of Pressure Vessels, Division 3
Alternative Rules For Construction Of High Pressure Vessels
- ASME BPVC Sec IX Boiler And Pressure Vessel Code, Section Ix, Welding And
Brazing Qualifications
- ASME BPVC Sec X Fiber-Reinforced Plastic Pressure Vessels
- ASME 579-1 Fitness for Service
- ASME RTP-1 Reinforced Thermoset Plastic Corrosion-Resistant Equipment
- ALPEMA The Standards pf the Brazed Aluminium Plate-fin Heat Exchanger
Manufacturers Association
- BS 2790 Specification for design and manufacture of shell
boilers of welded construction
- BS 799-5 Oil burning equipment: Carbon steel oil storage tanks
Specification
- and 3000 l - Design, construction and testing
- BS EN 1993-4-2 Eurocode 3-Design of steel structures - Tanks
- BS EN 9809-1 & 2 Gas cylinders-Refillable seamless steel
gas cylinders - Design, construction, testing
- BS EN 11120 Gas cylinders - Refillable seamless steel tubes of
water capacity between 150 l
- BS EN 12952 Water-tube boilers and auxiliary installations
- BS EN 12953 Shell boilers
- BS EN 13121 series GRP tanks and vessels for use above ground
- BS EN 13445 series Unfired pressure vessels
- BS EN 13923 Filament wound FRP pressure vessels
- BS EN 14015: Specification for the design and manufacture of
site built, vertical, cylindrical, flat-bottomed, above ground, welded,
steel tanks for the storage of liquids at ambient temperature and above
- EEMUA PUB No 143 Recommendations for Tube End Welding: Tubular
Heat Transfer Equipment (Part 1 Ferrous Materials)
- IOGP S-613 Specification for Air Dryer Packages
- IOGP S-614 Supplementary Specification to API Standard 660 Shell-and-Tube
Heat Exchangers
- IOGP S-619 Specification for Unfired, Fusion Welded Pressure Vessels
- ISO 10961 Gas cylinders - Refillable seamless steel tubes of water capacity
between 150 l and 3000 l - Design and construction
- ISO 13704 Petroleum, petrochemical and natural gas industries
Calculation of heatertube thickness in petroleum refineries
- ISO 13705 Petroleum, petrochemical and natural gas industries
Fired heaters for general refinery service
- ISO 13706 Petroleum, petrochemical and natural gas industries
Air-cooled heat exchangers
- ISO 15547 series. Petroleum, petrochemical and natural gas
industries Plate-type heat exchangers
- ISO 16812 Petroleum, petrochemical and natural gas industries
Shell-and-tube heat exchangers
- ISO 18796-1 Petroleum, petrochemicals and natural gas
industries Internal coating and lining of carbon steel process vessels
Part 1: Technical requirements
- PD 5500 Unfired Fusion Welded Pressure Vessel
- TBK-1-2 General Rules for Pressure Vessels
- TEMA Standards of the Tubular Exchangers Manufacturers
Association
- WRC Bull 107 Welding Research Council Local Stresses in
Spherical and Cylindrical Due to External Loading
- WRC Bull 297 Welding Research Council Local Stresses in
Spherical and Cylindrical Shells Due to External Loading on nozzles
Supplement to WRC Bull 107
|
Copyright 2022 Clasifications Register Group Limited, International Maritime Organization, International Labour Organization or Maritime
and Coastguard Agency. All rights reserved. Clasifications Register Group Limited, its affiliates and subsidiaries and their respective
officers, employees or agents are, individually and collectively, referred to in this clause as 'Clasifications Register'. Clasifications
Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance
on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant
Clasifications Register entity for the provision of this information or advice and in that case any responsibility or liability is
exclusively on the terms and conditions set out in that contract.
|
![](LR-FooterLogo.png) |
|