Appendix 2

NAME OF ADMINISTRATION
CERTIFICATE OF TYPE APPROVAL FOR 15 PPM BILGE ALARM
This is to certify that the 15 ppm Bilge Alarm, comprising the equipment listed below, has been examined and tested in accordance with the requirements of the specifications contained in part 2 of the annex to the Guidelines and Specifications contained in IMO resolution MEPC.107(49). This Certificate is valid only for the 15 ppm Bilge Alarm referred to below.
15 ppm Bilge Alarm supplied by ..........................................................................................
under type and model designation and incorporating: ................................................................................................................
15 ppm Bilge Alarm analysing unit manufactured by ..........................................................
to specification/assembly drawing No. ............................................ date ...........................
Electronic section of 15 ppm Bilge Alarm manufactured by ...............................................
to specification/assembly drawing No. ............................................ date ...........................
* Sample feed pump manufactured by ................................................................................
to specification/assembly drawing No. ............................................ date ...........................
*Sample conditioning unit manufactured by ........................................................................
to specification/assembly drawing No. ............................................ date ...........................
The 15 ppm Bilge Alarm is acceptable for use in accordance with regulation 14.7.
A copy of this Certificate should be carried aboard a vessel fitted with this 15 ppm Bilge Alarm at all times.
Test data and results attached as appendix.
Official stamp	Signed: .......................................................
	Administration of ........................................
	Dated this ................ day of ............ 20 .....
* Delete as appropriate.

APPENDIX
TEST DATA AND RESULTS OF TESTS CONDUCTED ON A 15 PPM BILGE ALARM IN ACCORDANCE WITH PART 2 OF THE ANNEX TO THE GUIDELINES AND SPECIFICATIONS CONTAINED IN IMO RESOLUTION MEPC.107(49)

15 ppm Bilge Alarm submitted by ........................................................................................

Test location ........................................................................................................................

Method of sample analysis ..................................................................................................

Samples analysed ...............................................................................................................

Environmental testing of the electronic section of the 15 ppm Bilge Alarm has been carried out in accordance with part 3 of the annex to the Guidelines and Specifications contained in IMO resolution MEPC.107(49). The equipment functioned satisfactorily on completion of each test specified on the environmental test protocol.

..............................................................................................................................................

CALIBRATION TEST AND RESPONSE TIME
Test Fluid	A		B		C
Test Fluid	Measured	Grab sample	Measured	Grab sample	Measured	Grab sample
0 ppm
15 ppm
Full scale (ppm)
Water Temperature		°C		°C		°C
Re-zero	Yes/No		Yes/No		Yes/No
Recalibrate	Yes/No		Yes/No		Yes/No
Response Time		sec		sec		sec

CONTAMINANT(S) AND COLOUR TEST
		Non-oil particulate matter
		Meter reading shift with ppm non-oil particulate contaminants and with very salt water.

		Oil Content Meter Reading
Clean water and 10 ppm Test Fluid “B”		ppm
Very salt water		ppm
Iron Oxide	10 ppm	ppm
Iron Oxide	50 ppm	ppm
Iron Oxide	100 ppm	ppm

SAMPLE PRESSURE OR FLOW TEST
	15 ppm Bilge Alarm reading shift at 50% of normal	... ppm
	15 ppm Bilge Alarm reading shift at 200% of normal	... ppm
	Deviations from this test should be stated if necessary
SHUT OFF TEST
	15 ppm Bilge Alarm reading before shut-off	... ppm
	15 ppm Bilge Alarm reading after start-up
	(minimum dry period 8 hours)	... ppm
	Damage to 15 ppm Bilge Alarm as follows:
	............................................................................................................................
	............................................................................................................................
	............................................................................................................................
UTILITIES SUPPLY VARIATION TEST
	110% voltage effects	...........................................................
	90% voltage effects	...........................................................
	110% air pressure effects	...........................................................
	90% air pressure effects	...........................................................
	110% hydraulic pressure effects	...........................................................
	90% hydraulic pressure effects	...........................................................

OTHER COMMENTS

..............................................................................................................................................

CALIBRATION AND ZERO DRIFT TEST
Calibration drift	... ppm
Zero drift	... ppm
Signed ................................................. Dated .............................................. Official stamp
(Official stamp or equivalent identification and the date of approval to be placed on all pages of the test protocol)