Belize - Specific requirements by the Belize Administration
Flag instructions relating to Statutory surveys
Flag procedural requirements
| Standing requirements | Action by |
|---|---|
| 1- Reporting on entry into class | MOC |
| 2- Reporting on requests for exemptions or interpretations | MOC |
| 3- Reporting on cases of major deficiencies, as per IACS Recommendation No. 98 (Duties of surveyors under statutory conventions and codes) | MOC |
| 4- Pre-authorisation prior to extending statutory certificates | MOC |
| 5- Pre-authorisation prior to issuing conditional term certificates | MOC |
| 6- Reporting on detentions | DO-FM |
| 7- Submission of copies of statutory certificates | DO-FM |
| 8- Reporting on class suspension or class modification | MOC |
| 9- Reporting on class withdrawal | DO-FM |
General policy
Agreement
An agreement has been signed between Recognised Organisation (RO) and the Belize Flag Administration on 10/04/2002 (refer to Agreement governing the delegation of statutory certification services).
The Annexes to the Agreement have been revised on 06/10/2014 (refer to Annex 1 to the Agreement and Annex 2 to the Agreement).
Issuance of Short-Term, Provisional and/or Extended certificates
(MMN-24-003)
Short-Term and/or Extended Certificates shall not be issued without prior authorization from the Administration. When a Short-Term or Extended Certificate is issued, the Administration shall also issue a Dispensation, which must be kept on board and presented to PSC officials upon request.
All Dispensations shall be subject to verification of alternative arrangements by Recognised Organisation (RO) and the provision of supporting documents (e.g., agreements with service providers, technician reports, purchase agreements for spares) to the Administration. Additionally, these alternative arrangements must be communicated to the crew, pilot, PSC, or any other interested party as required.
Recognised Organisation (RO), must, upon identifying conditions that affect the validity of a full-term certificate and cannot be rectified at the survey port, or when initial verification for SMC, ISSC, and MLC cannot be completed, promptly notify the Administration.
If necessary, Recognised Organisation (RO) shall request authorization from the Administration to downgrade the vessel’s full-term certificate(s) to a short-term or extended certificate(s), or, in the case of initial verification for SMC, ISSC, and MLC, issue provisional (short term) certificates.
Recognised Organisation (RO) shall provide the Administration with all alternative arrangements or supporting documentation as may be necessary in support of such a request.
The initial audit for compliance with the Safety Management Certificate (SMC), International Ship Security Certificate (ISSC), and Maritime Labour Convention (MLC 2006) standards, including onboard verification, must be completed within the validity period of the Interim Certificate (six months). If the full-term certificate cannot be issued immediately following this audit, Recognised Organisation (RO) may issue a Provisional Certificate (short term in Recognised Organisation (RO) terminology), which will be valid for up to five months from the date of the initial audit.
Recognised Organisation (RO) must also request authorization from flag before survey and certification of vessels engaged on single delivery voyage.
Before issuing Short-Term Certificates for Single Delivery Voyages, Recognised Organisation (RO) must thoroughly verify the vessel’s seaworthiness in accordance with the relevant conventions. The certificates shall clearly outline the conditions under which they are issued.
Aside from single delivery voyages, a Short-Term or Extended Certificate issued due to deficiencies or defects that cannot be immediately rectified must be accompanied by a Dispensation Letter issued by the Administration.
Change of name
(TN 00-0006)
Untitled
Where the Administration has effected the change of name on the registration documents (patent of navigation, ship station license, minimum safe manning certificate), the owner shall make sure that the new name has been marked on the ship and its lifeboats, lifebuoys, manuals, etc. and shall request the Recognised Organization to issue new statutory certificates bearing the new name of the ship.
Untitled
No new statutory certificate, bearing the new name, is issued until the required marking in all the required places and equipment has been completed and verified by the society surveyor.
Expired registration documents
(TN 00-0003)
No statutory certificate is either endorsed or renewed to a ship showing expired patent of navigation or ship radio station license.
Reporting to the Administration
Reporting relative to special authorizations in accordance with authorization for services outside the scope of Annex 1 to the Agreement (refer to Annex 1 to the Agreement) will be dealt with as mutually agreed on case-by-case basis.
Recognised Organisation (RO) shall provide to the Administration prompt written notification when Recognised Organisation (RO) suspends, withdraws or cancels class, when certificates issued under Annex 1 to the Agreement (refer to Annex 1 to the Agreement) are invalidated, or when the ship’s operational limitations are significantly altered, with appropriate explanation for such actions.
(MMN-23-003)
Before rendering any service to a Belize registered ship, Recognised Organisation (RO) must submit a request for authorization. This request should contain the list of certificates to be issued on behalf of Belize along with the scope of survey. Recognised Organisation (RO) cannot render any service prior to receiving an official authorization.
When an Initial or Renewal survey has been conducted and a Short-Term or Interim Certificate is issued, a written confirmation in a period no longer than thirty (30) days after the date of issuance shall be sent, along with copies of all certificates issued.
In cases where a Full-Term Certificate cannot be issued prior to the expiration date of the Short-Term or Interim Certificate, a prompt notification with at least twenty (20) days before the expiration date of the Short-Term or Interim Certificate shall be sent to the Technical Department allowing the Administration to take preventive measures.
When Full-Term Certificates are issued, a written confirmation in a period no longer than thirty (30) days after the date of issuance shall be sent, along with copies of all certificates issued.
When Annual/ Periodical/ Intermediate surveys are completed, a written confirmation shall be sent in a period no longer than thirty (30) days after the date of endorsement, along with copies of all certificates endorsed.
In cases where Recognised Organisation (RO) cannot arrange to conduct a Renewal/ Annual/ Periodical/ Intermediate survey within the window, rendering the certificates invalid, a prompt notification with at least twenty (20) days before the expiration date of the Short-Term or Interim Certificate shall be sent allowing the Administration to take preventive measures.
In cases where Recognised Organisation (RO) suspends or withdraw the certification of a vessel due to overdue surveys or outstanding recommendations, a notification shall be sent as soon as the certificate becomes invalid.
In addition to the above instructions, Recognised Organisation (RO) is instructed to not conduct any overdue survey nor to extend any statutory certificate beyond the stipulated period of validity without requesting an authorization to Administration’s Technical Department. For these cases, Administration’s Technical Department will proceed in accordance with regulation 5.6 “Revalidation of Certificates” and regulation 5.0 “Recommended Conditions for extending the period of validity of a certificate” of the latest edition of the IMO Resolution regarding “Survey Guidelines under the Harmonized System of Survey and Certification (HSSC).”
All notifications should be sent to Administration’s Technical Department by means of an email to technicalservices@immarbe.com containing all information required in this notice. Submission of certificates can be done either in electronic format or through a link with proper access and instructions on how to download all certificates using the Recognised Organisation (RO) web-based platform.
Circulars and Merchant Marine Notice
Refer to:
- the websites of the Administration:
http://www.immarbe.com/publications-and-news/circulars/
https://www.immarbe.com/belize-maritime-publications/merchant-marine-notice/
- The List of Technical Department Notices (in attached file “TDL-009r22-ListofTechnicalDepartmentNotices.pdf”)
Fees
Refer to the related procedure.
Electronic Certificates
(Administration email dated 23/01/2018)
Certificates may be issued in an electronic format according to FAL.5/Circ.39/Rev.2
Change of status from operational to maintenance, dry-docking, repairs, or laid-up
(MMN-21-001)
All Belize registered vessels with intention to change its status from operational to dry-docking, under repair, maintenance or laid-up shall notify IMMARBE’s Technical Department of this intention along with the period needed under the new status.
Any Belize registered vessels authorized for above-mentioned change of status will be provided with a Statement of Authorization issued by the Administration.
Shipowners and ISM Operators must get in contact with Recognised Organisation (RO) and inquire about the procedure for change of status to avoid suspension or cancellation of the vessel certification. In order to have a Statement of Authorization the Owner/Operator shall submit to the Administration a non-inconvenience confirmation of the change of status from Recognised Organisation (RO).
Centralized email for IMMARBE technical services
(Memo SDR 03-21)
All email queries for technical services should be sent to technicalservices@immarbe.com
The following format should be followed when requesting a service from the Technical Department:
Example: Exemption Certificate— Vessel Name “Big Blue“ (IM0#xxxxxx)
Requirements for Handling Port State Control Inspections and Detentions
(MMN-25-006)
The vessel operator must notify the Administration without delay following a Port State Control detention. The notification, including the PSC Report Forms A and B, must be submitted via email to inspections@immarbe.com. Concurrently, the operator must arrange for the attendance of Recognised Organisation (RO) to verify the rectification of deficiencies. Recognised Organisation (RO) is required to carry out a comprehensive inspection of the vessel to identify any additional deficiencies beyond those cited in the PSC report.
Where the PSC inspection report cites deficiencies related to the International Safety Management (ISM) Code, Recognised Organisation (RO) (when responsible for ISM) must conduct an additional Safety Management system [SMS) audit onboard the vessel. In cases where five or more ISM-related deficiencies are identified, the Administration may require an additional audit of the company’s Document of Compliance (DOC) within 30 days.
If the date of the detention falls within a 13-month window of the vessel's annual survey, Recognised Organisation (RO) must conduct the annual surveys at the port of detention to the extent practicable. Should the surveys be impractical due to extenuating circumstances at the detention port, Recognised Organisation (RO) must notify the Administration and provide a detailed schedule for their completion at the next port of call. Exceptions apply to the Safety Equipment and Radio surveys, which remain mandatory and must be completed at the detention port.
Where deficiencies affect the validity of statutory certificates and cannot be rectified immediately, the relevant certificate should be downgraded to a short-term certificate. Recognised Organisation (RO) should contact the flag regarding these deficiencies and propose temporary arrangements and provide supporting documentation. Upon flag agreement, Recognised Organisation (RO) will be granted the necessary authorization to downgrade the statutory certificate. Additionally, the vessel must be issued a dispensation letter via the vessel’s designated office in accordance with the latest revision of MMN-24-003 (see Issuance of Short-Term, Provisional and/or Extended certificates).
Recognised Organisation (RO) shall:
Attend the vessel at the detention port to confirm deficiency rectification and conduct a genera] inspection.
Perform annual surveys if detention falls outside the +/-3-month window for mandatory surveys.
If surveys cannot be completed, notify the Administration and provide a completion schedule.
Conduct an additional Safety Management Certificate (SMC) audit if ISM deficiencies are cited. For cases with more than five (5) ISM deficiencies, conduct a Document of Compliance (DOC) audit of the company within 30 days.
Downgrade affected certificates to short-terrn (with Flag Administration approval).
Advise operators to apply for a dispensation letter when a short-term certificate is required on board.
Submit all findings and corrective actions to the Administration.
Occasional Survey Program
(TD-IMM-GOB-001-25)
From 23/05/2025, any vessel detained will receive a Notice of Warning and immediately enter the occasional survey program in accordance with the scenarios listed in section 7.6 of TD-IMM-GOB-001-25 for a cumulative period of 24 months starting from the date of the detention.
This occasional survey will be conducted by the RO in charge of Statutory Certification. In cases of mixed ROs, the RO in charge of the statutory certificates will oversee the Occasional Survey program.
Upon satisfactory completion of the Occasional Survey, the RO shall issue a Statement of Compliance (SoC) with a validity of six (6) months confirming the satisfactory result of the Occasional Survey performed.
The Occasional Survey can be advanced to coincide with the annual, intermediate, or renewal survey, but it may not be delayed for these same reasons.
The scope of the occasional survey shall be equivalent to an annual mandatory survey in compliance with International and National requirements. If deficiencies are found, Recognised Organisation (RO) must report these findings immediately to the Administration with evidence of corrective actions. If the deficiency cannot be rectified before the departure, Recognised Organisation (RO) shall follow the guidance set forth in MMN-24-003 (see Issuance of Short-Term, Provisional and/or Extended certificates).
Recognised Organisation (RO) shall:
that vessels under the OSP are inspected every six months as required by this policy.
After completion of each occasional survey, Recognised Organisation (RO) must issue a Statement of Compliance (SoC) and submit a copy of same along with the Survey Report, supported with photo report(s) to inspections@immarbe.com.
establish appropriate mechanisms to be notified of each occasional survey due date and inform owners at least 30 days before the date.
report to the Administration if an OSP cannot be completed by the due date, or if the owners/operators fail to cooperate in arranging the OSP, at least 15 days before the due date to allow for flag intervention.
To the satisfaction of the Administration
(MMN-23-004)
The Administration will consider in the first instance the interpretations developed and approved by the International Maritime Organization (IMO). In their absence, the unified interpretation approved by the International Association of Classification Societies (IACS) may be used as a base to establish specific requirements to comply with certain provisions of the relevant international instruments.
However, if the Administration is not satisfied with any unified interpretation or no interpretation exists, then, its own interpretation will be established through the Circulars or through individual statements according to the specific case and will be considered on a “case by case basis”.
Type-approved equipment or systems acceptance
(MMN-23-005)
The equipment will be considered as accepted by the Administration in the following two (2) circumstances:
Equipment provided in technical specifications or operating standards of the International Maritime Organization (IMO), in which cases they have been developed and approved within the IMO Committees. Recognised Organisation (RO) must accept its use for equipment onboard Belize registered ships.
Equipment not addressed by technical specifications or operating standards approved by the International Maritime Organization (IMO) in which the relevant international instrument simply provide that the equipment must be type-approved, the Administration will accept:
Equipment approved by traditional maritime countries that are members of the IMO, which have national, regional, or international provisions for the approval of certain types of equipment; therefore, Recognised Organisation (RO) must accept such approved equipment.
Equipment approved under the standards developed by specialized International Organizations and recognized by the IMO, such as the unified interpretations of the International Association of Classification Societies for equipment or materials onboard.
Change of flag, RO, RSO and ISM Operator
(Merchant Marine Notice MMN-24-007)
Change of flag survey with no change of RO
At the time of change of flag, if the due dates for surveys of exisitng certificates fall within the +/- 3 months window, then the renewal/intermediate/periodical/annual surveys/audits shall be carried out immediately.
If the change of flag is not accompanied by a change of Company, the surveys shall be limited in scope to the applicable annual survey.
If the change of flag is accompanied by a change in the ISM Company, the scope of surveys for safety equipment must be upgraded to that of the renewal survey.
Surveys for statutory certificates other than the safety equipment shall be conducted in line with annual surveys and intermediate audits as required.
Change of flag survey with change of RO
In the case of change of flag and change of RO, the scope of surveys/audits must meet the requirements for a renewal survey/audit.
Change of Company
When there is a change of ISM Company/Operators, the owners/operators shall apply to the RO for the re-issuance of relevant certificates.
Additionally, owners/operators must apply to Administration through their designated office for new CSR, MSMC and DMLC Part I Certificates to reflect the change in the ISM, as required by the DOC, ISM, ISMS audits and MLC, 2006 inspections.
Change or transfer of RO and or RSO
For the gaining RO/RSO:
Prior to accepting any request for a transfer of vessel certification, the gaining RO/RSO shall notify the Administration of such a request by providing the general particulars of the Company and vessel and details of the survey/ audit requested using Form TDF-033 Recognized Organization Survey Request (attached file).
The gaining RO/RSO must review all existing certificates and documentation to ensure that the ship’s certificates have not been withdrawn or invalidated by the Administration or the losing RO.
All outstanding recommendations given by the losing RO/RSO must be followed up and rectified before the transfer, unless otherwise agreed by the Administration.
Any major non-conformity must be closed out or downgraded by the losing RO/RSO.
No transfer of certification shall be performed by the gaining RO/RSO without conducting the necessary surveys/ audits.
The surveys/audits conducted by the gaining RO/RSO must address all elements of the relevant Conventions, Codes, Statutory Instruments, Circulars, Merchant Marine Notices and the Belize Merchant Ships (Registration) Act (in its latest revision), as adopted by the Administration.
If the transfer of certification occurs within the +/- 3-months window of the mandatory surveys / audits, those mandatory surveys / audits shall be conducted at that time.
If the surveys/audits are not successful, the transfer of certification shall be considered invalid. The gaining RO/RSO shall inform the Administration immediately with a full explanation of the reasons for such failures.
Mixing of ROs
The Administration does not permit the mixing of ROs except in cases where one RO is responsible for all statutory certificates and another is responsible for DOC, SMC, ISSC audits, MLC 2006 and CICA inspections (see also note in ).
Reporting of deficiencies relating to possible ISM failure
(MSN-0032)
The purpose of this MSN-0032 is to instruct Recognised Organisation (RO) to notify the Administration when deficiencies relating to possible safety management failures are identified during any type of Survey; i.e. periodical, occasional, class, statutory or additional surveys relevant to Port State Control, Flag State Inspections or any other not mentioned herein.
The kind of deficiencies that should be reported by Recognised Organisation (RO) to the Administration are provided in Annex 1 of MSN-0032, but can be summarized as follows:
deficiencies relating to technical conditions that would lead to the limitation, suspension or withdrawal of a Statutory Certificate or Class in the case of those vessels in which such limitation, suspension or withdrawal of Class may affect the Statutory Certification status;
deficiencies relating to the documentation of the vessel and/or crew;
deficiencies relating to operational requirements affecting the safety of navigation and marine environment;
other deficiencies which may directly or indirectly affect the working environment and living conditions in detriment of the Human Element.
LL 66
Freeboard calculation
(TN 00-0002)
No Load Line certificate is issued to a ship registered in Belize unless a freeboard calculation is conducted by the Society and made available, upon request, to the Administration.
SOLAS 74
Cargo Ship Safety Construction Certificate
Outside Ship's Bottom Inspection Requirements
(MMN-18-001r1)
Spontaneous Dry-Docking Survey
If a vessel sustains damage or requires emergency dry-dock repairs, such dry-docking will not be considered a mandatory dry-docking survey unless all required surveys under international conventions are performed under the supervision of the Recognized Organization on behalf of the Administration.
Before accepting such a survey as a mandatory dry-docking survey, Recognised Organisation (RO) must obtain prior agreement from IMMARBE’s Technical Department. Recognised Organisation (RO) surveyors shall attend and supervise the spontaneous dry docking survey and submit a narrative report along with the Dry Dock Survey Report or Underwater Survey Report, detailing the inspected areas, repairs, and any pending items. This request must align with Item 3.6 of Merchant Marine Notice 17-002, “Reporting of Casualty and Incident (in its latest revision).”
Underwater Inspection in Lieu of Dry-Docking (UWILD)
Inspections of the outside ship’s bottom should typically be conducted in a dry dock. However, consideration may be given to alternative inspections performed with the ship afloat under specific conditions.
The Administration establishes the UWILD eligibility criteria based on vessel age and type (refer to MMN-18-0001).
Dry-Docking Extensions
IMMARBE may consider granting dry-docking extensions only in accordance with this Merchant Marine Notice, under SOLAS Ch. I Regulation 14(e) or 14(f), or if no shipyard is available. In such cases, the maximum non-extendible period is three (3) months.
Request for dry-docking extension shall be made by the Owner/Manager to IMMARBE’s Technical Department, and should include a written acceptance from Recognised Organisation (RO) with the latest Ship Survey Status.
Cargo Ship Safety Equipment Certificate
Adjustment of magnetic compasses and deviation curves
(TN 00-0005)
As a general principle, the compass deviation should be checked regularly and recorded. The record should be readily available to show the measured deviations over a range of magnetic headings. As long as these measured deviations agree with those shown on the ship's deviation curve, there is no requirement to readjust the compass.
The ship’s deviation curve should show a smooth curve with no rapid changes with the measured deviations following some pattern. A change in either the shape of the curve or in the values is an indication that the compass requires to be readjusted.
Where ships carry similar deck loads or other cargoes regularly, there may be value in the ship's staff drawing up separate deviation curves for determined conditions of loading.
An accurate deviation curve showing an effectively adjusted compass is an important navigational tool and is requested by the generally, or one prepared for a particular condition of loading, is to be kept readily available for use.
Requirements for Approval of Service Providers, thorough examination, operational testing, overhaul and repair of lifeboats and rescue boats, launching appliances and release gear (MSC 402(96))
(MMN-20-001)
This MMN provide procedures for approval of an Organization other than the manufacturer concerning the requirements for maintenance, thorough examination, operational testing, overhaul and repair of lifeboats and rescue boats, launching appliances and release gear as required by MSC 402(96).
Any inspections, maintenance, thorough examination, operational testing, overhaul and repair shall be carried out according to the maintenance manuals and associated technical documentation developed by the manufacturer.
(Manufacturer means the original equipment manufacturer (OEM) or any entity which has taken legal and legitimate responsibilities for equipment when the OEM no longer exists or supports the equipment.)
In case where a manufacturer is no longer in business or no longer provides technical support, in accordance with paragraph 7.3 in Annex 1 of the Res. MSC 402(96), the Administration may authorize service providers for the equipment on the basis of prior authorization for the equipment and/or long-term experiences and demonstrated expertise as an authorized service provided.
Qualification levels and certification
Below mentioned sections are in accordance with Res. MSC 402(96).
Weekly and monthly inspections and routine maintenance as specified in the equipment maintenance manual(s), shall be conducted by authorized service providers, or by shipboard personnel under the direction of a senior ship’s officer in accordance with the maintenance manual(s)
Annual thorough examinations and operational tests, as described in section 6.2, shall be conducted by certified personnel or either the manufacturer or an authorized service provider in accordance with section 7 & 8. The service provider may be the ship operator provided that it is authorized in accordance wit section 3 &7.
Five-year thorough examination, any overhaul, overload operational tests, as described in section 6.3 and repair shall be conducted by certified personnel of either the manufacturer or an authorized service provider in accordance with section 7 & 8.
Requirements for authorization of service providers
The Administration may authorize Service Providers to carry out the inspection, maintenance, thorough examination, operational testing, overhaul and repair of lifeboats and rescue boats, launching appliances and release gear provided that the service provider demonstrate the following:
- Employment and documentation of personnel certified in accordance whit a recognized national, international or industry standards as applicable or a manufacturer’s established certification programme. In either case, the certification programme shall comply with section 8 of Res. MSC 402(96) for each make and type of equipment for which the service is to be provided,
- availability of sufficient tools,
- access to appropriate parts and accessories as specified for maintenance and repair,
- availability of the manufacturer’s instructions for repair work involving disassembly or adjustment of on-load mechanisms and davit winches
- a documented and certified quality system,
- in lieu of the above, the Administration may accept or recognize service providers on case by case basis if the service provider is approved by the attending RO or an IACS RO.
Statement of Extension
In the event that the maintenance, thorough examination, operational testing, overhaul and repair of lifeboat and rescue boats, launching appliances and release gear cannot be conducted along with the annual survey for the Cargo Ship Safety Equipment Certificate / Passenger Ship Safety Certificate within the period (+/- 3 months) due to exceptional circumstances, a Statement of Extension needs to be requested from the Administration.
The issuance of Statement of Extension shall be determined in coordination with the RO which may require additional requirements.
Responsibility of the Service Provider
Upon completion of the maintenance, thorough examination, operational testing, overhaul and repair of lifeboat and rescue boats, launching appliances and release gear a Certificate of Inspection or similar shall be issued valid until the last date of the window period (+/- 3 months) of the Cargo Ship Safety Equipment Certificate / Passenger Ship Safety Certificate.
A copy of the Certificate of Inspection or similar shall be submitted to the Administration.
Responsibility of the RO
The maintenance, thorough examination, operational testing, overhaul and repair of lifeboat and rescue boats, launching appliances and release gear shall be done in the presence of the ship’s RO surveyor who shall verified on behalf of the Administration that the servicing and inspection provided by the service provider is carried out in accordance with the Res. MSC 402(96).
The Cargo Ship Safety Equipment Certificate / Passenger Ship Safety Certificate will be endorsed only once the RO has been satisfied that the servicing and inspection has been carried out in accordance with the Res. MSC 402(96).
Responsibility of the owner / ISM operator
The owner or ISM operator shall ensure that the maintenance, thorough examination, operational testing, overhaul and repair of lifeboat and rescue boats, launching appliances and release gear referred in Res. MSC 402(96) are completed at the date of the survey (Cargo Ship Safety Equipment Certificate / Passenger Ship Safety Certificate)
For further information, refer to the attached file “MMN-20-001.pdf”.
Emergency Escape Breathing Devices in Machinery Spaces
(MSN-0007)
The number of EEBDs to be carried within machinery spaces shall be not less than the total number of persons during watch.
A minimum of two devices shall be carried in the engine room of ships provided with Un-attended Machinery Spaces (UMS).
Emergency Escape Breathing Devices shall be located in way of the escape routes, control spaces and/or workshops where practicable or at the foot of escape ladders other than the escape trunks.
In addition to any spare designated for accommodations spaces, a spare EEBD solely for the machinery space shall be carried onboard in addition to the numbers described above.
The number and location of these devices shall be indicated in the fire control plan.
LRIT
(MMN-24-006)
In cases where the vessel’s LRIT testing has failed, remains pending, or where the LRIT/AIS cannot report due to a defect, the vessel operator must immediately inform the Flag State, Recognised Organisation (RO), and, if applicable, the Port or Coastal State authorities.
Recognised Organisation (RO), after assessing the specific circumstances of the non-compliance, shall submit the details to the Administration and request authorization to issue a short-term CSSE certificate.
Additionally, the operator must request a Dispensation Certificate from the Administration via their Designated Office. This certificate must be kept on board until the issue prompting the Short-Term certificate is resolved.
Cargo Ship Safety Radio Certificate
GMDSS - Manning
(Message of 07/09/1998)
Ships with shore-based maintenance engaging on voyage beyond sea area A1 shall be manned with:
two deck officers both holding a General Operator Certificate (GOC), or
one dedicated radio officer holding a General Operator Certificate (GOC).
Ships with on-board maintenance engaging on voyage beyond sea area A1 shall be manned with:
one dedicated radio officer holding either a 1st or a 2nd class Radioelectronic Certificate (REC) and one deck officer holding a General Operator Certificate (GOC), or
one holder of either a 1st class or a 2nd class Radioelectronic Certificate (REC) not designated as the Radio Officer and two deck officers both holding a General Operator Certificate (GOC).
Ships engaging on voyage exclusively within sea area A1 shall be manned with one deck officer holding a General Operator Certificate.
Passenger Ship Safety Certificate
Others
IP Code
(MMN-24-002)
The Administration has decided to delegate the issuance of the Industrial Personnel Safety Certificate and the Record of Equipment (Form IP) to its authorized RO (Recognised Organisation (RO) is therefore fully delegated).
MARPOL 73/78
Annex I. IOPP certificate
Accelerated single hull tankers phase-out and Condition Assessment Scheme (CAS)
Merchant Shipping Notice MSN-0014 (September 15, 2004) as amended by fax TD/F/05/016 dated 29/06/2005 is attached in MSN-0014 - Accelerated single hull tankers phase-out and CAS application.
Annex II. NLS certificate
Annex IV. ISPP certificate
(MSN 0037)
The revised Annex apply to existing ships registered at IMMARBE by the 27th September 2008 as follows:
Ships engaged on international voyages of 400 GT and above, and
Ships engaged on international voyages of less than 400 GT and certified to carry 15 persons or more.
Every ship to which Annex IV applies shall be equipped with either a sewage treatment plant or a sewage comminuting and disinfecting system or a sewage holding tank.
Annex V
Regulations for the Prevention of Pollution by Garbage from Ships
Annex VI
Use of halogenated hydrocarbons (halons)
(Refer to Merchant Shipping Notice 0019 in MSN 0019 - Use of halogenated hydrocarbons (halons))
With the entry into force of Annex VI of MARPOL 73/78, Regulation 12 on air pollution (19 May 2005) new installations of fixed systems and portable fire-extinguishing units using ODS are prohibited on all ships.
Servicing to existing systems
All precautionary measures practicable shall be taken to prevent and minimise leakages of controlled substances inadvertently produced in the course of testing, repairing, maintaining, servicing or disposal of halon-containing systems or equipment.
In addition to the mandatory annual leakage check of halon fire-extinguishing systems required under MSC/Circ.600, a leakage test of an equipment or system containing halon needs to be conducted prior its repairing, maintaining, servicing or disposal.
Record of the tests mentioned above should be kept onboard for inspection by IMMARBE and the Recognized Organization if so required.
It will be the owners / operators duty and responsibility to notify immediately to IMMARBE of emissions arising from leaks of an ozone depleting substance whether or not the leaks were deliberate.
Ships found to have less than fully charged fixed halon fire-extinguishing system for machinery spaces and other spaces, i.e. with a shortage of halon quantities required for the satisfactory operation of its system, while in a port where halon is not available, shall contact IMMARBE along the procedures described in MSC/Circ.775.
Disposal and decommissioning
The disposal of halon shall be done through a recognized halon banking and reception facility licensed to provide such service. The latest list of such facilities is contained in circular FP.1/Circ.31 (periodically updated) from the Fire Protection sub-committee of the IMO.
Vessels currently registered with IMMARBE that are equipped with fixed fire protection systems and / or fire extinguishers containing halon, such systems shall be decommissioned not later than the 1st January 2010.
Data Collection System (DCS) for Fuel Oil Consumption of Ships
(Merchant Marine Notice MMN-18-002 r2, dated 16/10/2019)
Recognised Organisation (RO) is authorized to perform the following statutory services:
Reviewing of SEEMP Part II and issuance of Confirmation of Compliance, (MARPOL Annex VI, Regulation 5, para. 4.5)
Verification of reporting data, (MARPOL Annex VI, Regulation 22A)
Issuance of Statement of Compliance (MARPOL Annex VI, Regulation 5, para. 4.5)
Submission of reported data to the IMO Ship Fuel Oil Consumption Database ((MARPOL Annex VI, Regulation 22A, para. 9)
Recognised Organisation (RO) shall submit the Statement of Compliance along with a full report of each submission to the IMO Ship Fuel Oil Consumption Database to IMMARBE’s Technical Department at following email: technicalservices@immarbe.com
For further information refer to attached file “MMN-18-002r2.pdf”.
Implementation of the 2020 Sulphur Limit
(Merchant Marine Notice MMN-19-001)
The Administration encourages ships flying their flag to develop Implementation Plans, outlining how the ship may prepare in order to comply with the required Sulphur content limit of 0,50% by 1 January 2020 and strongly recommended to follow the Guidance in accordance with the MEPC.1/Circ.878.
When carrying out any statutory surveys during 2019, Recognised Organisation (RO) will verify if the vessel has implemented this non-mandatory implementation plan or if proper actions have been taken when the global 0,50% m/m sulphur limit enters into effect.
In case the vessel is found without implementation plan, incomplete implementation plan or without proper actions taken, the same shall be notified to the Administration to IMMARBE Technical Department: technicalservices@immarbe.com for proper record and further actions, but not as means of deficiency.
For further information, refer to attached file “MMN-19-001”.
EEDI, EEXI and CII
(MMN-22-001)
The Administration has decided to delegate requirements regarding EEDI to all authorized RO acting on its behalf (Recognised Organisation (RO) is therefore authorized).
The RO in charge of the issuance of the IAPP to a specific vessel shall carry out the verification process of this vessel in accordance with the Guidelines developed by the Organization. Upon completion of the verification process, Recognised Organisation (RO) is authorized to issue the International Energy Efficiency Certificate (IEEC) on behalf of the Administration.
The International Energy Efficiency Certificate (IEEC) shall be submitted via e-mail to IMMARBE’s Technical Department to technicalservices@immarbe.com.
(MMN-22-004)
The Administration has decided to delegate requirements regarding EEXI, SEEMP and CII to all authorized RO acting on its behalf (Recognised Organisation (RO) is therefore authorized).
The RO in charge of the issuance of the IAPP to a specific vessel shall carry out the verification process of this vessel.
Upon completion of the verification process, the RO is authorized to issue the Confirmation of Compliance - SEEMP Part III on behalf of Belize, and to submit it via e-mail to the IMMARBE’s Technical Department: technicalservices@immarbe.com
Exemptions for Unmanned Non-Self-Propelled (UNSP) Barges
(Merchant Marine Notice MMN-22-005)
Definition of Unmanned Non-Self-Propelled (UNSP) Barge is given in this Merchant Marine Notice MMN-22-005.
Recognised Organisation (RO) in charge of the issuance of the International Oil Pollution Prevention Certificate (MARPOL Annex I), the International Sewage Pollution Prevention Certificate (MARPOL Annex IV) and the International Air Pollution Prevention Certificate (MARPOL Annex VI) to a specific vessel shall be capable to:
Satisfactory review of the submitted plans (General Arrangement Plan, Capacity Plan) and other relevant information to confirm the condition referred to in regulation 3.7 of MARPOL Annex I, regulation 3.2 of MARPOL Annex IV, or regulation 3.4 of MARPOL Annex VI, as appropriate, are met.
Perform a survey of the UNSP barge to confirm if the actual arrangements on board comply with the exemption conditions, as appropriate.
Based on satisfactory result of the survey, certificates for exemption of a UNSP barges from certain survey and certification requirement should be issued by Recognised Organisation (RO) on behalf of Belize.
The exemption certificate shall be in the format required by relevant MARPOL Annex and with a validity of maximum 5 years, and be submitted via e-mail to the IMMARBE’s Technical Department: technicalservices@immarbe.com
BWM Convention
General
(Letter of authorization TWIMC-17S-0034 dated 18/07/2017 and MMN-17-003)
Recognised Organisation (RO) is authorized to:
perform surveys in accordance with Regulation E-1 and to issue a BWM Statement of Compliance as Belize has not yet ratified the BWM Convention
to approve BWM Plans (Regulation B-1)
to approve BWM Systems (Regulation D-3)
Recognised Organisation (RO) classed ships under Belize are to be issued with a relevant International BWM Statement of Compliance by 8th September 2017 (even if a ship is only required to comply with Regulation D-1 at that time) for inspection by Port State Control (PSC).
The Administration accepts BWM System Type Approvals issued by other Administrations or by an IACS member.
For further information, refer to attached file “TWIMC-17S-0034 Recognised Organisation (RO) AUTHORIZATION LETTER (BWM Convention)”
Tonnage 69
Tonnage calculation
(TN 00-0002)
No tonnage certificate is issued to a ship registered in Belize unless a tonnage calculation is conducted by the Society and made available, upon request, to the Administration.
Tonnage forms for non-convention ships
(Administration email dated 16/03/2020)
- TDF-022 Survey Report for Non-Convention Tonnage Certificate (“TDF-022.pdf” attached)- TDC-038 Certificate of Tonnage Measurement for Non-Convention Vessel (“TDC-038.doc” attached)
AFS Convention
Untitled
(MSN-0034)
Belize has not yet ratified the AFS Convention, therefore it will not be mandatory for vessels registered with IMMARBE to comply with the Convention, nevertheless companies may voluntary avoid the use of tin-based anti-fouling systems and be surveyed in accordance with Resolution MEPC.358(78) on Guidelines for survey and certification of anti-fouling systems on ships and be issued with a Statement of Compliance by Recognised Organisation (RO).
ILO Conventions
ILO convention No. 92 and No. 133 - Crew accommodation certificate
(Merchant Shipping Notice MSN-0017)
Application
With effect from the 1st March 2006, all Belize registered vessels shall comply with the provisions for Crew Accommodation contained in the International Labour Organization Convention No. 92 and No. 133
Exceptions
Untitled
The provisions of these Conventions shall apply to all Belize registered vessels of 500 gt (ITC) and above, with the exception of;
Fishing vessels,
Ships of war and troopships,
Wooden ships of primitive build,
Pleasure crafts not used for commercial purposes,
Un-manned vessels,
Tugs,
Vessels trading in territorial waters of anyone country.
Untitled
All or any of the provisions of these conventions may be applied whenever reasonable and practicable, as determined by the Administration, to vessels between 200 gt and 500 gt, which are;
engaged on international trade, and/or
carrying dangerous goods, and/or
carrying more than 10 persons.
Untitled
Vessels to which the criteria listed under Untitled do not apply, may request the issuance of an exemption certificate from the Administration.
Exemptions
The Administration may grant exemptions from all or any of the provisions of these conventions (as may be specified in the exemption) on such terms (if any) as the Administration may so specify and may, subject to reasonable notice, alter or cancel such exemption.
Vessels applying for an exemption certificate to the Administration will need to provide in addition to a written application, the reasons for the particular request endorsed by the RO which performed the related survey onboard the vessel.
Responsibilities of companies and masters
Untitled
Every company responsible for the operation of a ship(s) under the Belize registry shall ensure that:
The crew accommodation shall be maintained in a clean and habitable condition and all equipment and installations required by these regulations shall be maintained in good working order.
Every part of the crew accommodation, except store rooms, shall be kept free from stores and other property not belonging to or provided for the use of persons for whom that part of the accommodation is appropriated, and in particular no cargo shall be kept in any part of the crew accommodation.
The master of the ship or an officer appointed by him for the purpose shall inspect every part of the crew accommodation at weekly intervals and may be accompanied on the inspection by at least one member of the crew. The particulars of such inspections shall be recorded in the official logbook.
Any substantial alteration or reconstruction to the crew accommodation or crew number increase beyond the maximum capacity shall be reported to the Administration and shall be subject to an occasional inspection to ensure that such modifications are in compliance with the terms of the Convention.
Survey and certification
It will be the company’s and master’s responsibility to arrange for the survey of their vessels.
Upon satisfactory completion of the survey requirements relevant to the convention, a full term crew accommodation certificate valid for five (5) years from the date of the initial survey will be issued by the Recognized Organization surveying the vessel on behalf of the Administration.
Refer to:• the “Record of Approved Cargo Ship Crew Accommodation (Ad 2320)” available in ASMS Record part,
• the “Crew Accommodation Certificate ILO 92 and 133” available in ASMS National Certificate part.
Miscellaneous technical requirements
Marine equipment
(Message dated 10 January 2000)
The society is authorised to perform surveys or inspections on board in-service ships or new buildings to ensure conformity of the marine equipment with European Directive 96/98/EC.
Cargo ships in the Caribbean trading area
(TN 01-99)
Untitled
Ships less than 500 grt operating in the Caribbean trading area shall comply with the provisions of the code of Safety for Caribbean Cargo Ships (CCSS code) and shall hold a certificate of compliance. This is a requirement applicable to ships in the entire area and not solely to those trading with the United States.
Untitled
Cargo ships of less than 500 grt but more than 300 fall under the scope of SOLAS Chapter IV. They shall comply with the applicable GMDSS provisions and shall hold a Cargo Ship Safety Radio Certificate.
Untitled
Cargo ships less than 300 grt shall comply with provisions of Chapter 5 (Radio-communications) of the CCSS Code. The certificate of compliance and the attached form of record of equipment and ship information show compliance with the applicable requirements. They need not any additional document and no Non-Convention Safety Radio Certificate shall be issued to these ships.
Cargo ships less than 500 grt
Untitled
Cargo ships less than 500 grt are subjected to the provision of the statutory instrument No. 147 (1991) as amended by the statutory instrument No. 82 (1997) attached in Cargo vessels under 500 grt.
Untitled
They shall be issued with an International Load Line Certificate as applicable within the scope of the Load Line Convention. They shall also hold a tonnage certificate, an IOPP certificate and a SOPEP.
Untitled
They shall also hold a non-convention Cargo Ship Safety Construction Certificate and a non-convention Cargo Ship Safety Equipment Certificate. Cargo ships less than 300 grt shall hold a non-convention Cargo Ship Safety Radio Certificate. These non-convention certificates are available in ASMS Certificates Editor.
Fishing vessels of 24 m and above
Untitled
Fishing vessels of 24 m and above are subjected to the provisions of the Statutory Instrument No. 113 (1995) attached in Fishing vessels of 24 m in length and above.
Untitled
They shall hold a tonnage certificate, and, where applicable, an IOPP certificate and a SOPEP.
Untitled
They shall hold a Fishing Vessel Safety Certificate. The survey for the issuance of this certificate covers load lines, safety construction, safety equipment and safety radio items. As far as radio-communications are concerned, also refer to Radio-communications. The Fishing Vessel Safety Certificate is available in ASMS Certificates Editor.
Radio-communications
(TN 02-99 as amended by TN 00-0004)
Untitled
Fishing vessels certified to operate within 20 miles of land and remaining within VHF coverage of a coast station are fitted with:
VHF EPIRB,
VHF radio-telephone installation (a transceiver capable of operating on channels 6, 13 and 16).
Untitled
All other fishing vessels are fitted with, as a minimum:
MF radio-telephone installation (a transceiver capable of operating on 2182 kHz and working frequencies between 1605 kHz and 2850 kHz),
VHF radio-telephone installation (a transceiver capable of operating on channels 6, 13 and 16),
automatic float-free satellite EPIRB,
with a crew member holding a restricted radio-telephone operator permit.
Untitled
Fishing vessels of 75 m or more in length are fitted with:
INMARSAT ship earth station (C, M, A or B),
MF radio-telephone installation (a transceiver capable of operating on 2182 kHz and working frequencies between 1605 kHz and 2850 kHz),
VHF radio-telephone installation (a transceiver capable of operating on channels 6, 13 and 16),
automatic float-free satellite EPIRB,
if operated more than 150 miles from land, provided with two methods of maintenance,
if operated less than 150 miles from land, provided with one method of maintenance,
with a deck officer holding a general operator certificate.
Fishing vessels operating within or landing products in the European Union
All new fishing vessels of 24 m in length and over and existing fishing vessels of 45 m in length and over shall comply either with the requirements of SOLAS, Chapter IV or with the requirements of Directive 97/70/EC, Chapter IX.
the building or major conversion contract is placed on or after 1 January 1999 or
the building or major conversion contract has been placed before 1 January 1999 and which is delivered 3 years or more after this date, or
in the absence of a building contract, on or after 1 January 1999:
the keel is laid, or
construction identifiable with a specific ship begins,
assembly has commenced comprising at least 50 tonnes or 1% of the estimated mass of all structural material, whichever is lesser.
An existing fishing vessel is a fishing vessel which is not a new fishing vessel.
Paris MoU pilot PSC
(MMN-24-001)
Given the accident statistics and the increasing regulations of fishing vessels, the Paris MoU is conducting a pilot on PSC on Fishing Vessels to evaluate whether it could be of added value to implement a harmonized approach to port State control on internationally operating fishing vessels of 24 meters and above. Upon completion of the pilot period, a report will be submitted to the Paris MoU Port State Control Committee for further analysis and decision.This pilot will be conducted in 2024 and 2025 and will be held by a limited number of Paris MoU members: Canada, Croatia, Denmark, France, Germany, Ireland, Netherlands, Norway, Spain, and United Kingdom.
Recognised Organisation (RO) that will carry out any statutory surveys shall ensure with immediate effect that items related to the mentioned 9 criteria in MMN-24-001 (attached file) are covered with special attention to the vessel and living conditions.
Pleasure vessels
Refer to interpretation of pleasure yacht or pleasure craft definition under S.I. 148 of 1991 - See Merchant Shipping Notice MSN-0016 attached in MSN-0016 - Interpretation of pleasure yacht or pleasure craft definition under S.I. 148 of 1991.
Specific forms for Pleasure Craft/Yacht
- PLEASURE CRAFT CHECKLIST FORM (Fillable Form) (“TDF-21.pdf” attached)
- CERTIFICATE OF COMPLIANCE FOR PLEASURE CRAFT (“TDC-039.doc” attached)
- CERTIFICATE OF COMPLIANCE FOR PRIVATE YACHT (“TDC-040.doc” attached)
Yachts in commercial or private use
(MMN-25-009)
The Administration has developed three distinct Codes of Standards for Yachts, categorized primarily by length and Gross Tonnage:
The code of standards for yachts of 24 m or above and 500 GT or more but less than 5000GT – The Super Yacht Code
The code of standards for yachts of 24 m or above and less than 500 GT – The Large Yacht Code
The code of standards for yachts of less than 24 m but not less than 10 m – The Small Yacht Code
These codes come into effect on 1st June 2008.
The actual texts of the codes and relevant information may be requested from the Administration directly by email at technicalservices@immarbe.com or viewed on the Administration web-page at:
https://www.immarbe.com/regulatory-framework
These codes are mandatory for all new registrations of yachts in commercial use and are strongly recommended for those in private use. Existing commercial yachts may remain under the current arrangements for a period up to 24 months from the date of entry into force of these codes.
The template for the CoC provided by the INMARBE is in the attached file “F-102-PCY”.
On the header of the certificate the words “COMMERCIAL”or “PRIVATE” must be crossed out as appropriate so as to state the applicable yacht's provisions.
In the space for IMO / LRF No., a N/A must be inserted if this number is not applicable to the vessel or it has not been provided with one.
Paragraph No. 1 of the certificate should be completed with the name of the relevant code (as applicable).
In paragraph No. 2 the word “commercial” or “private” must be crossed out as appropriate
OSV Chemical Code
(MMN 18-003)
The Administration delegates the survey and issuance of the Certificate of Fitness under the OSV Chemical Code to Recognised Organisation (RO).
For further information, refer to attached file “MMN-18-003f”.
Ship Recycling & Inventory of Hazardous Material (IHM)
Survey and Certification - IHM
(Administration email dated 17/06/2020, MMN-20-004)
Recognised Organisation (RO) is duly authorized to survey and certify Belize registered vessel in accordance with the Hong Kong Convention and the EU SRR.
The Statement of Compliance issued to any ship survey in accordance with the European Union Ship Recycling Regulation (EU-SRR) must be in accordance with the format (Annex 3) provided by the Guidance on inspection of ships by the port States in accordance with Regulation (EU) 1257/2013 on ship recycling, inspections from the EU port States to enforce provisions of the ship recycling regulation.
The initial and renewal survey must be harmonized with the surveys required by other applicable statutory instruments of the Organization following the parameters of the HSSC Guidelines in its latest version.
(Administration email dated 31/12/2020)
Due to the Covid-19 pandemic and the associated difficulties in the surveying of ships, the European Union launched the official Journal of the European Union C 349 (see attached file “Official Journal of the European Union C 349.pdf”) with common guidelines to ensure a harmonized approach towards enforcement by the EU port States authorities during ship inspections as of 1 January 2021. Two temporary options have been made available for vessels that are not in compliance with the IHMs requirement due to Covid-19 restrictions. Scenarios 1 Vessels without a valid IHM and/or accompanying certificate In this case, the vessel may arrive at an EU port after 31 December 2020 without carrying on board a valid IHM and/or accompanying certificate (Inventory Certificate or Ready for Recycling certificate for EU flagged vessel or Statement of Compliance for non-EU flagged vessel) and the shipowner/master claims that this non-compliance is due to the Covid19 situation. Scenarios 2 Vessels with a semi-completed IHM with an associated approved Inventory Certificate or Ready for Recycling Certificate (for EU flagged ships) or the Statement of Compliance (for non-EU Flagged ships), that does not contain onboard (either targeted or random) samplingIn this case, the vessel may call at an EU port or anchorage after 31 December 2020 with an IHM and associated certificate on-board, but the IHM was prepared remotely without any on-board sampling. This situation may arise as the on-board surveys that should have been undertaken to support the IHM could not be done because of the restrictions on inspecting a vessel during the Covid-19 pandemic. Actions required In either case, the owner/operator shall provide evidence that all possible measures were taken to undertake the work and get the certification required. Such evidence of compliance efforts may include a service contract for sampling or a survey. It may also include a justification for why it was not possible to obtain a semi-completed IHM and associated certificate. Where the IHM has been semi-completed, a conditional statement of compliance valid for 3 months shall be issued by Recognised Organisation (RO). In all cases, every effort shall be made to ensure that all vessels not yet in compliance with the IHMs are properly surveyed and certified no later that 31st March 2021.
ISM Code
Authorizations & instructions
| Ship type | PS | PH | PR | BC | OT | CT | GC | CH | CS | MO |
Document of Compliance | ||||||||||
| Interim | x | x | x | x | x | x | x | x | x | x |
| Initial | x | x | x | x | x | x | x | x | x | x |
| Periodical | x | x | x | x | x | x | x | x | x | x |
| Additional | x | x | x | x | x | x | x | x | x | x |
| Renewal | x | x | x | x | x | x | x | x | x | x |
Safety Management Certificate | ||||||||||
| Interim | x | x | x | x | x | x | x | x | x | x |
| Initial | x | x | x | x | x | x | x | x | x | x |
| Intermediate | x | x | x | x | x | x | x | x | x | x |
| Additional | x | x | x | x | x | x | x | x | x | x |
| Renewal | x | x | x | x | x | x | x | x | x | x |
Note: | See also Issuance of Short-Term, Provisional and/or Extended certificates (Merchant Marine Notice MMN-24-007)
| |||||||||
| Requirements of the Administration | Action by |
|---|---|
| Report full details of owner / operator / designated person as indicated in “reference documents”. | CD |
Circular letter from 1st April 2009: Seafares endorsements from IMMARBE. Refer to the attached file “CIRCULAR LTR DG 05 09 SEAFARERS ENDORSEMENTS”. | Auditors |
Procedures concerning observed ISM code major non-conformities (IMO MSC/Circ.1059 - MEPC/Circ.401 - 16/12/2002) applied. This Circular is displayed in database “Statutory Info”. | CSQM |
Fax dated 12/09/97: Authorisation with regard to ISM code. |
| Fax ref. TD/F/03/03 dd 12/03/200: ISM code - Major non-conformities |
Reporting of full details of owner / operator / designated person
Background
Considering the responsibility of the Administration to properly and fully implement the provisions of the ISM code as mandated by the international convention for the Safety Of Life At Sea (SOLAS, Chapter IX),
Taking into consideration that, the procedures described herein, where not followed during Phase I of the implementation of the ISM code, and bearing in mind that Phase II of the ISM Code will be due to enter into force on the 1st July 2002 for all cargo ships and MODUs.
Entry into force
This Technical Note shall take effect as to the date of issue / acknowledgement of receipt.
Application
The present Technical Note shall be implemented by all deputy registrars, resident agent, registration department (HO).
Actions requested
Untitled
All deputy registrars without exception shall contact the owners / operators of the existing vessels under their records to whom the ISM code phase I applied and gather the information contained in F-043-DISM, “Reporting of Owners / Operators / Designated Person”, attached to this Technical Note.
Untitled
The registration forms shall be properly filled and sent to the Administration for the vessel files.
Untitled
The registration department (HO), for every vessel to whom phase I of the ISM code applies, who is requesting a provisional or permanent status, shall follow the same procedure.
Untitled
The requirements described herein shall become mandatory falling into phase II of the ISM code (1 July 2002), as to the date of entry force of such.
Refer to the attached file “Reporting”.
Maritime Cyber Risk Management
(Refer to MMN-20-007, attached file “MMN-20-007 Maritime Cyber Risk Management in Safety Management System.pdf”)
Cyber risks should be appropriately identified, analyzed, and addressed within the Safety Management System no later than the first annual verification of the Document of Compliance after 1st January 2021. To that end, owners need to identify and manage cyber risks the soonest as possible in preparation for the first annual verification of the company’s document of compliance after 1 January 2021.
The purpose of MMN-20-007 is to provide information on the requirement to incorporate maritime cyber risk management in the safety management system (SMS) of companies.
Emergency Power Supply Testing (Tokyo MoU Safety Bulletin)
(Refer to TDM004-2024)
When conducting ISM audits related to emergency generator functionality on ships, the following actions should be considered:
Testing Emergency Generator Functionality: During inspections and audits, Recognised Organisation (RO) is to ensure that the emergency generator is tested using both the “simulated blackout” routine/sequential test switch and a controlled blackout (as previously described). If there is a discrepancy between the results of these tests, corrective actions should be taken.
Addressing Discrepancies: If the test using the simulated blackout switch is satisfactory but the controlled blackout test is not, necessary actions should be taken. This could involve amending the emergency generator test procedures or ensuring that the test switch circuit paths allow for a complete test of the emergency generator.
Modifications and Documentation: Any required modifications to the routine/ sequential test switch circuit paths should be approved by Recognised Organisation (RO). Changes to the emergency generator testing procedure should be documented in the ship’s safety management system and preventative maintenance system.
Responsibility for Electrical System Design and Approval: The design and approval of the electrical system are the responsibilities of Recognised Organisation (RO), ensuring compliance with SOLAS requirements.
ISPS Code
Authorizations & instructions
| SSP approval / review | Ship audit | ISSC issuance |
|---|---|---|
| Yes | Yes | Yes |
Observation(s): Website: http://www.immarbe.com/publications-and-news/circulars/ > Regulation of Merchant Ships (Ship Security) Regulation 2004, S.I N° 90 of 2004 > Maritime security guidelines for ships registered at IMMARBE Security Coordinator: security@immarbe.com | ||
| Item | Specific requirements | Observation(s) |
|---|---|---|
| Language required | ||
| MSA qualification | ||
| SSP approval / review | Guidelines for each security level (ICS) attached to circular mentioned above. | |
| Minimum period of SSP implementation on board | ||
| SSA and SSP according to specific template | ||
| TOSCA | See MMN-24-007 Section 7 | |
| SSP amendments | To be approved by Recognised Organisation (RO). | |
| CSO / SSO Training / qualification | ||
| ISSC issuance | See Issuance of Short-Term, Provisional and/or Extended certificates | |
| Annex to ISSC (related to Part B) | ||
| Audit reports submission to Administration | ||
| Minimum period for filing records | Security records: 5 years. | |
| Ship Security Alert System (SSAS) | Ensure it transmits the alert to the Company. After receiving an alert, CSO informs the Administration. | |
| Document of reference | Annex 1 to the Agreement. | |
MLC, 2006
Scope of authorisation
| Yes | No | Observation | |
|---|---|---|---|
| Approval of DMLC II | X |
| Inspection | Certification | ||
|---|---|---|---|
| Yes | No | ||
| Full recognition (Recognised Organisation (RO) is RO) | X | X | |
See also Issuance of Short-Term, Provisional and/or Extended certificates Note: Belize ratifies the Convention on 8th of July 2014 | |||
Specific Flag requirements
Extracts from Resolution DG-004 – The Maritime Labour Convention 2006
Quote
2. Application
Ships
1 Except as expressly provided otherwise, this resolution applies to all ships, whether publicly or privately owned, ordinarily engaged in commercial activities, other than ships engaged in fishing or in similar pursuits and ships of traditional build such as dhows and junks. This resolution does not apply to warships or naval auxiliaries.
2 The following ships shall be inspected and certified to be in compliance with the requirements of the convention and carry and maintain a Maritime Labour certificate (ML certificate) and the Declaration of Maritime Labour Compliance (DMLC) Parts I and II issued in English:
i. Ships of 500 gross tonnage or over, engaged in international voyages;
ii. Ships of 500 gross tonnage or over, operating from a port, or between ports, in another country; and
iii. Other ships, as may be voluntarily requested by a shipowner.
3 Inspection and certification procedures for these ships are provided in Part F of this resolution.
4 The convention allows for flexibility in implementation by providing for national determinations, substantial equivalencies, and exemptions and variations under certain provisions.
5 The requirements in the code implementing Regulation 3.1, Accommodation and recreational facilities, apply only to ships constructed on or after the date when the convention enters into force. A ship shall be deemed to have been constructed on the date when its keel is laid or when it is at a similar stage of construction. For ships constructed before that date, the requirements relating to ship construction and equipment that are set out in the Accommodation of Crews Convention (Revised), 1949 (No. 92), and the Accommodation of Crews (Supplementary Provisions) Convention, 1970 (No. 133), shall continue to apply to the extent that they were applicable, prior to that date.
Seafarers
7 Except as expressly provided otherwise, this resolution applies to all seafarers on board Belizean flagged ships to which the Maritime Labour Convention applies.
8 The MLC, 2006 recognizes in Article II, paragraph 3, that there may be doubts whether a particular category or categories of persons who may perform work on board a ship covered by the convention should be regarded as seafarers. Recognizing that there is need for clarification on this subject to help to provide uniformity in the application in the rights and obligations provided by the Convention, the 94th (Maritime) session of the International Labor Conference adopted Resolution VII, to assist Administrations in resolving any difficulties that may arise.
9 The Belize Maritime Administration will consider the following issues, as provided for in Resolution VII, in determining whether certain persons or category of persons are considered seafarers:
i. the duration of the stay on board of the persons concerned;
ii. the frequency of periods of work spent on board;
iii. the location of the person’s principal place of work;
iv. the purpose of the person’s work on board; and
v. the protection that would normally be available to the persons concerned with regard to their labor and social conditions to ensure they are comparable to that provided for under the Convention.
10 The Belize Maritime Administration, taking into account the criteria provided in Resolution VII, considers that the following persons will not generally be considered as seafarers for the purpose of the MLC, 2006:
i. Professional pilots;
ii. Port workers;
iii. Guest entertainers;
iv. Ship inspectors / surveyors;
v. Ship superintendents;
vi. Repair and maintenance technicians; and
vii. Technical personnel in platforms or MODU (Mobile Offshore Drilling Units)
11 For the purposes of this resolution, and with regards to offshore drilling platforms or MODUs, persons who, due to their training and qualifications are covered by the regulations of the STCW convention, shall be considered seafarers.
Unquote
Seafarers Employment of Agreement (SEA)
The Administration is asking to conduct a review of the crew employment contract or SEA and ensure that no crewmen is employed with expired contract or service on board witch exceeds the less than 12 months limit.
Refer to the Merchant Marine Notice MMN-20-005 in attached file “MMN-20-005”.
2014 Amendments to the MLC, 2006
(MMN-26-005)
Recognised Organisation (RO) is to include in MLC inspection checklists the verification covering both Regulation 2.5 (Repatriation) and Regulation 4.2 (Shipowner's Liability) and to ensure that these requirements are properly examined during the initial, intermediate, and renewal inspections.
2018 Amendments to the MLC, 2006
(MMN-20-006)
2018 Amendments concern:
Seafarer’s Employment Agreements
Wages
Entitlement
These Amendments do not immediate affect the validity of the MLC Certificate nor the validity of the DMLC Part I. Existing MLC Certificates and DMLAC Part I issued by the Administration will remain valid until the 1st initial/renewal MLC inspection on or after 26 December 2020.
Changes to the DMLC Part II are not necessary, unless there are pre-existing references that contravene the 2018 Amendments.
During initial/renewal MLC inspection, Recognised Organisation (RO) must verify compliance with the 2018 Amendments.
New DMLC Part I after 26 December 2020 will include the 2018 Amendments.
For further information, referto the attached file “MMN-20-006.pdf”.
2022 Amendments to the MLC, 2006
(MMN-24-011r1)
Vessels entering service after 23 December 2024 must comply with the amended MLC standards.
For existing vessels, the existing Maritime Labour Convention (MLC) certificates and associated Declarations of Maritime Labour Compliance (DMLCs) shall retain their validity. However, with the 2022 amendments to the Convention entering into force on 23 December 2024, vessels must confirm compliance with these amendments no later than the date of their first renewal inspection following this date, as it pertains to certification.
To demonstrate full compliance with the 2022 amendments, vessel operators must complete and submit Form TDF-034, “Declaration of Compliance with Maritime Labour Convention 2006 Amendments 2022,” to technicalservices@immarbe.com confirming that the amendments are in effect for their fleet. Additionally, a copy of the completed Declaration Form TDF-034 must be kept on board and presented to PSC officials upon request.
Shipowners must submit an updated DMLC Part II to the Recognised Organisation (RO), outlining the measures adopted to ensure continuous compliance with the new requirements. This submission must be made as soon as practicable but no later than the next renewal date of the MLC certificate.
Recognised Organisation (RO) shall verify that the vessel is provided with a new Declaration of Maritime Labour Compliance (DMLC) Part 1 and 2 no later than the date of the first renewal inspection following entry into force of the amendments.
Appendix — Agreement governing the delegation of statutory certification services
Agreement
Refer to the attached file “Agreement_Belize_RO_10042002”.
Appendix — Annex 1 to the Agreement
Applicable instruments and degree of authorization
Refer to the attached file “Annex1_Belize_RO”.
Appendix — Annex 2 to the Agreement
Reporting to the Administration
Refer to the attached file “Annex2_Belize_RO”.
Appendix — Cargo vessels under 500 grt
Statutory Instrument No. 147 of 1991 as amended by S. I. No. 82 of 1997
Refer to the attached file “S.I.147of1991asAmendedS.I.82”.
Appendix — Check-list of safety items for vessels under 500 grt
Untitled
Refer to the attached file “Check-list of Safety Items for vessels under 500 grt”.
Appendix — Fishing vessels of 24 m in length and above
As amended by Statutory Instrument No. 113 of 1995
Refer to the attached file “Fishing vessels of 24 m in length and above”.
Appendix — Registration of Merchant Ships (Pleasure Vessels) Regulations, 1991
Statutory Instrument No. 148 of 1991
Refer to the attached file “S.I.148of1991”.
Appendix — Administration’s Merchant Shipping Notices
List of Technical Department Notices
Refer to Circulars and Merchant Marine Notice
MSN-0010 Instructions to ROs on PSC detentions and surveys
Refer to the attached files “MSN-0010”, “Check-sheetForSurveyOfILOitems” & “Annual Survey ISM Check-list”.
MSN-0014 - Accelerated single hull tankers phase-out and CAS application
Refer to the attached file “MSN-0014”.
MSN-0016 - Interpretation of pleasure yacht or pleasure craft definition under S.I. 148 of 1991
Refer to the attached file “MSN-0016”.
MSN 0019 - Use of halogenated hydrocarbons (halons)
Refer to the attached file “MSN-0019”.
Appendix — Specific Certificates: National and bilingual International certificates
List of National certificates
Safety certificates
- Cargo Ship Safety Construction certificate
- Cargo Ship Safety Equipment certificate
- Cargo Ship Safety Radiotelephony certificate
- Fishing Vessel Safety certificate
- Crew Accommodation Certificate (ILO 92/133)