Cook - Specific requirements by the Cook Islands Administration

Cook

Flag instructions relating to Statutory surveys

Flag procedural requirements

Standing requirements
Standing requirementsAction by
1- Reporting on entry into classMOC
2- Reporting on requests for exemptions or interpretationsMOC
3- Reporting on cases of major deficiencies, as per IACS Recommendation No. 98 (Duties of surveyors under statutory conventions and codes)MOC
4- Pre-authorisation prior to extending statutory certificatesMOC
5- Pre-authorisation prior to issuing conditional certificatesMOC
6- Reporting on detentionsDO-FM
7- Submission of copies of statutory certificatesDO-FM
8- Reporting on class suspension or class modificationMOC
9- Reporting on class withdrawalDO-FM

Additional Flag instructions

 
10- Reporting on expired statutory certificatesMOC

General policy

Agreement

An Agreement has been signed between Recognised Organisation (RO) and the Cook Islands Administration (Office of the registrar of shipping; Department of trade, labour and transport) starting on 29 April 2016 (see Agreement governing the delegation of statutory certification services to Annex 2 to the agreement).

Authorizations for service outsides the scope of Annex 1 to this Agreement (see Annex 1 to the Agreement) will be dealt with , as mutually agreed on a case-by-case basis

In so far as the statutory certification and services covered by this Agreement are concerned, Recognised Organisation (RO) agrees to co-operate with the Port State Control officers to facilitate the rectification of reported deficiencies on behalf of the Administration , when so requested, and report to the Administration.

An Amendment to the Agreement has been signed between the Government of the Cook Islands and Recognised Organisation (RO) Marine & Offshore SAS entering into force on 01 January 2017 (see Agreement governing the delegation of statutory certification services).

Reporting to the Administration

With reference to the services performed pursuant to this Agreement, Recognised Organisation (RO) agrees to provide the Administration with the following:

  • Notification of class suspension, withdrawal or classification of the ships registered in the Cook Islands

  • Notification of cases where a ship did not in all respects remain fit to proceed to sea without danger to the ship or person on board or presenting unreasonable threat of harm to the marine environment.

Interpretations, Equivalents and Exemptions

While interpretations of the applicable instruments, as well as the determination of equivalents or the acceptance of substitutes to the requirements of the applicable instruments are the prerogative of the Administration, Recognised Organisation (RO) will co-operate in their establishment as necessary. Recognised Organisation (RO) applies the IMO interpretations and Circulars, as well as the available IACS Unified Interpretations, unless provided with written instruction to apply a different interpretation by the Administration.

Exemptions from the requirements of the applicable instruments are the prerogative of the Administration and must be approved by the Administration prior to issuance.

In instances where, temporarily, the requirements of an applicable instrument cannot be met under particular circumstances, Recognised Organisation (RO) will accept, after consulting with and gaining approval from the Administration, such measures or supplementary equipment as may be available to permit the vessel to proceed to a suitable port where permanent repairs or rectifications can be effected or replacement equipment fitted.

The Administration reserves the right to suspend, cancel or revoke any certificate, document or approval issued by Recognised Organisation (RO) pursuant to this agreement. The Administration will inform Recognised Organisation (RO) of the reasons for suspending, cancelling or revoking a statutory certificate.

Recognised Organisation (RO) may, having consulted with the Administration, suspend, cancel or revoke any statutory certificate issued on behalf of the Administration.

(Circular 257/2022 in attached files)

Requests for exemptions/waivers should include the applicable regulation to be exempted or waived, regulation that allows the exemption/waiver, and the expiry date of the relevant certificate. Depending on the actual Regulation to be exempted/waived, additional documentation to prove applicability could have to be submitted.Recognised Organisation (RO) may be requested to advise on existing arrangements onboard or mitigating measures adopted.

Surveyors

Recognised Organisation (RO) should perform survey and certification functions of a statutory nature by the use of only exclusive surveyors and auditors, being solely employed by Recognised Organisation (RO), duly qualified, trained and authorised o execute all duties and activities incumbent upon their employer, within their level of work responsibility.

However, if Recognised Organisation (RO) finds in exceptional and duty justified cases that its own exclusive surveyor is not available, Recognised Organisation (RO) shall inform the Administration, with an alternative nomination for the Administration’s consideration. The Administration may accept this alternative nomination, or nominate an exclusive surveyor of one other RO.

Recognised Organisation (RO) may also utilise the services of subcontractors and other support service providers in accordance with the relevant provisions of IMO Res. A789(19) and with the RO code, provided that such subcontractors and suppliers of support services are approved by Recognised Organisation (RO) or another RO.

Electronic Certificates

(Administration email dated 31/03/2021)

Recognised Organisation (RO) is authorized, upon Owner’s request, for ships flying the Cook Islands flag and for the delegated statutory certificates, to issue these certificates in an electronic format in accordance with IMO Guidelines FAL.5/Circ.39/Rev.2.

(Refer to Circular 248/2021)

The Administration has developed a new database system (Upvise) that enables the Adminstration to provide clients with electronic Certificates in accordance with the International Maritime Organization (IMO) guidelines as per FAL.5/Circ.39/Rev.2The new system is efficient and effective and not only enables the Administration to meet its obligations and responsibilities, MCI Deputy Registrars and Surveyors are now able to access real time vessel and client information as well as access to the latest versions of survey & Certification templates.

Cook Islands Approved Surveyors will be able to complete surveys using a mobile app installed on their mobile phones or tablets and upload the survey report immediately; the mobile app will allow surveyors to take photographs which will be automatically included into the survey report, so as to show compliance of the vessel or otherwise.

Extensions

(Circular 257/2022 in attached files)

Extensions

Queries must be submitted well in advance on the expiry date of the certificate or survey: at least one month for renewal surveys, dry bottom surveys and for other annual surveys/servicing (for example: annual service for liferaft).

Every query will be considered on a case-by-case basis, and it should be accompanied by documented evidence justifying the need of the extension. In case of dry dock survey extension requests, at least three different shipyards letters should be submitted.

Except for specific circumstances – to be documented – extensions will be granted for maximum 3 months without further postponements.

ISM, ISPS, MLC Extensions

Queries related to the ISM, ISPS, MLC Certification should be requested as per the below schedule:

  • SMC and ISSC: at least one month before the end of the renewal verification window

  • MLC: at least one month before the end of the renewal inspection window; extensions to the MLC certificate will be evaluated on a case-by-case basis and no extensions will be guaranteed for the Interim MLC certificate.

  • DOC: no extensions will be granted for the DOC inspections. The Administration can authorize, on a case-by-case basis, remote DOC verifications.

Dispensation

(Circular 257/2022 in attached files)

Requests should always be accompanied by supporting documentation proving the impossibility to fix the issue in the port where the vessel is, a proposed corrective action and mitigating measures to reduce the risk to sail not complying with a statutory requirement.

Recognised Organisation (RO) will be invited to issue a Conditional/Short term statutory certificate involved in the defect valid until dispensation expiry date.

LL 66

Multiple Load Lines

(Circular 264/2022)

Recognised Organisation (RO) is authorized to assign multiple load lines to Cook Islands flagged vessels, at the conditions specified below:

  1. Compliance with applicable rules and safety standards must be maintained regardless of the deadweight in use.

  2. Only one set of load line marks and corresponding certificate shall be in use.

  3. The attending Surveyor of Recognised Organisation (RO) issuing the Load Line Certificates must verify that the Load Line marks corresponding to the assigned freeboard are welded to the side shell, while the Load Line marks corresponding to the additional certificate/s are cut or punched into the side shell;

  4. Upon Owner’s request for change of freeboard, a Surveyor of Recognised Organisation (RO) must supervise/verify, also remotely according to the Recognised Organisation (RO) procedure, that the unassociated marks are painted out and that the new marks are painted in, and that certificate/s pertaining to the unused marks are placed in a sealed envelope and left in the custody of the Master.

  5. The Master is to make an entry in the ship’s official logbook and deck log book on every occasion that the load lines are changed.

  6. Procedure for change in load-line shall be included in the vessel’s safety management system.

  7. The vessel shall be surveyed in compliance with statutory requirements applicable to the maximum deadweight value corresponding to the assigned freeboard during statutory surveys. Upon completion of the surveys, all Load Line certificates shall be endorsed.

SOLAS 74

Cargo Ship Safety Construction Certificate

Lifting appliances and anchor-handling winches

(Circular 339/2026)

Existing lifting appliances and anchor-handling winches installed before 1 January 2026 shall be certified according to Regulation II-1/3-13 no later than the date of the first renewal survey of the Safety Construction Certificate on or after 1 January 2026. The Administration strongly recommends to carry out the required certification process at the first available survey of the Safety Construction Certificate on or after 1 January 2026, whether annual, intermediate or renewal.

Paragraphs 2.1 and 2.4 of SOLAS Regulation II-1/3-13 shall not apply to lifting appliances with a SWL of less than 1,000 kg. Nevertheless, procedures for maintenance, inspection and operational testing, including record keeping for lifting appliances with a SWL of less than 1,000 kg are to be duly established and maintained in the vessel’s onboard Safety Management System (SMS), taking into account the relevant IMO Guidelines.

For existing appliances, existing certificates issued under other international instruments - such as ILO Convention No. 152 - will be acceptable for compliance. If no valid certificate exists, a load test and thorough examination must be carried out no later than the first renewal survey after 1 January 2026.

Recognised Organisation (RO) shall verify during applicable surveys on or after 1 January 2026 that:

  • A full inventory of lifting appliances and anchor-handling winches is on board;

  • All appliances are marked and documented with SWL and other required data;

  • Valid certification, load test and thorough examination records are available;

  • Loose gear is identified by clear and permanent marking (serial number and SWL) and proof-tested;

  • All lifting appliances are provided with an operation and maintenance manual.

Cargo Ship Safety Equipment Certificate

Magnetic compass

(Circular 176/2018)

The Administration has decided to require the review of the Deviations cards every two years.

Magnetic compasses should be adjusted when:

  1. they are first installed;

  2. they become unreliable;

  3. the ship undergoes structural repairs or alterations that could affect its permanent and induced magnetism;

  4. electrical or magnetic equipment close to the compass is added, removed or altered; or,

  5. the recorded deviations are excessive out of “acceptable tolerance” (+/- 5°) or when the compass shows physical defects.

The adjustments of the magnetic compass must be carried out only by certified magnetic compass adjusters and the deviation card must by issued by them accordingly.

Each vessel shall contact the local Port State Authority where they are calling, in order to get the list of certified magnetic compass adjusters. Adjustments can not be carried out by Cook Islands Flag surveyors.

For further information, refer to attached file “Circular-1762018”.

ECDIS (Electronic Chart Display and Information Systems)

(Technical Circular 180/2018)

Surveyors shall check and collect, while carrying out the first survey (annual / periodical / renewal), whichever occurs earlier (related to Cargo Ship Safety Equipment and Passenger Ship Safety certificates) at least the followings:

  • ECDIS Type Approval Certificate in compliance with the applicable IMO Resolutions and performance standards, as above detailed;

  • Connection to emergency source of electrical power, gyro compass, speed log and GPS receiver;

  • Display of latest Electronic Navigational Chart (ENC) database, issued by an authorised Hydrographical Office, and conform to IHO applicable standards (IHO S-52, IHO S-64 and IEC 61174).

  • An up-to-date list of all the relevant IHO standards relating to ECDIS equipment can be accessed from the IHO website (www.iho.int);

  • The back-up arrangements of the ECDIS.

  • When navigation charts (hard copies) are supplied as backup, the charts shall need to be updated.

  • Certificate of attendance of the generic ECDIS training hold by Master and OOW(s).

For further information, refer to attached file “Technical-Circular_180-2018.pdf”.

Requirements for maintenance, thorough examination, operational testing, overhaul and repair of lifeboats and rescue boats, launching appliances and release gear (MSC 402(96))

(Circular 212/2019)

The Administration will accept only service providers authorised by other administrations or by their Recognised Organisation, specifically for each make and type of equipment on board of the vessel. Evidence of such authorisations shall be made available on board to FSI surveyors, attached to service reports.

The authorisation as service provider equally applies to manufacturers when they are acting as authorised service providers. In other words, a service branch of a manufacturer needs to obtain authorisation.

In cases where a manufacturer is no longer in business or no longer provides technical support, the Administration may authorize other service providers for the equipment based on prior authorisation for the equipment and/or long-term experience and demonstrated expertise as an authorized service provider. Documented evidence shall be provided to the Technical Department in order to get such authorisation.

Five-year thorough examination, any overhaul, overload operational tests and repairs shall be conducted by certified personnel of either the manufacturer or an authorised service provider. This shall be done in the presence of the vessel’s Classification surveyor.

For further information, refer to attached file “Circular 212-2019.pdf”.

Cargo Ship Safety Radio Certificate

Passenger Ship Safety Certificate

Other

Polar Code

Refer to attached Circular 340/2026.

MARPOL 73/78

Annex I. IOPP Certificate

Amendments to IOPP Form B (Resolution MEPC.276(70)

(Circular 166/2018)

Following entry into force of the above Amendment, to reflect the requirements relating to dedicated clean ballast tanks (CBTs) which were extinct due to phasing out of single hull tankers, the Administration requires that the revised IOPP Supplement Form B is issued to the concerned ships under Cook Islands flag at the 1st IOPP survey on or after 1 March 2018.

For further information, refer to attached file “Circular 166-2018”.

Annex II. NLS Certificate

Annex IV. ISPP Certificate

Regulation for the prevention of pollution by sewage from ships

Annex V

Regulation for the prevention of pollution by garbage from ships

Annex VI

Data Collection System for fuel oil consumption of ships

(Circular 169/2018)

Recognised Organisation (RO) is authorized to perform the following statutory services:

  • Reviewing of SEEMP Part II and issuance of “Confirmation of Compliance” (MARPOL Annex VI, Regulation 5.4.5)

  • Verification of reporting data, (MARPOL Annex VI, Regulation 22A)

  • Issuance of “Statement of Compliance “(MARPOL Annex VI, Regulation 6)

  • Submission of reported data to the IMO Ship Fuel Oil Consumption Database ((MARPOL Annex VI, Regulation 22A, para.9)

For further information, refer to attached file “Circular-169-2018”.

Ozone-Depleting Substances (Reg. 12)

(Circular 204/2019)

No Hydro-chlorofluorocarbons (HCFC) containing system or equipment is permitted to be installed on ships constructed on or after 1 January 2020 and no new installation of the same is permitted on or after that date on existing ships.

Existing systems and equipment are permitted to continue in service and may be recharged as necessary. However, the deliberate discharge of Ozone-depleting substances (ODS) to the atmosphere is prohibited.

For further information, refer to attached file “Circular-204_Ozone-Depleting-Substances”.

Early application of the verification procedures for a fuel oil sample

(Circular 210/2019)

In advance of their entry into force, the Administration apply the approved amendments to appendix VI of MARPOL Annex VI related to the verification procedure for a MARPOL Annex VI fuel oil sample (regulation 18.8.2 or regulation 14.8), providing an agreed method to determine whether the fuel oil delivered to, in-use or carried for use on board a ship is in accordance with the applicable sulphur limit of regulation 14 of MARPOL Annex VI.

For further information, refer to attached file “Circular_210-2019”.

Requirements on fuel oil sampling points

(Circular 258/2022)

For every ship subject to the application of MARPOL Annex VI, the sampling points shall be fitted or designated for taking in-use samples of the fuel being used on board of the ship, taking into account the guidelines set up in the MEPC.Circ.864/Rev.1, by the following schedule:

  • Existing ships – which are keel laid before 1st April 2022: not later than first IAPP renewal survey on or after 1st April 2023;

  • New ships – which are keel laid on or after 1st April 2022: on delivery.

Refer to MEPC.1/Circ.864/Rev.1 for sampling points location. While the preferred solution may be to designate already existing sampling points, fitting and designating new sampling points may in some cases be the only option. For such cases, the vessel’s Classification Society should be involved to verify the design, location, and fittings’ material.

EEXI and CII

(Circular 269/2022)

(Administration email dated 12/09/2022)

Recognised Organisation (RO) is authorised to carry out plan approval and survey as well as to issue the relevant certification, for what concerns the new measures to reduce carbon intensity that have been introduced by Resolution MEPC 328(76), in particular to:

  • Approve SEEMP Part III and issue the respective confirmation of compliance (this verification is not limited to ship’s RO and can be done by any ROs);

  • Verify the CII in accordance with the methodology specified in SEEMP part III;

  • Issue the SoC related to fuel oil consumption reporting and operational carbon intensity rating;

  • Submit the relevant CII related information and data to GISIS on behalf of the Cook Islands.

Other

Use of Electronic Log Data and Record Book Systems

(Circular 225/2020)

The Administration will allow the use of the Electronic Record Books (ERB) onboard its registered vessels, provided the following conditions:

  1. Manufacturers

    ERBs used onboard Cook Islands flagged vessels are required to be approved by the Administration. ERBs manufacturers can obtain such approval by providing the Administration with documentary evidence that the ERB has been approved by an IACS RO in accordance with MEPC.312(74) and relevant MARPOL regulations.

    If the ERB has been developed directly by an IACS RO, then the Administration will require the RO to submit a declaration of conformity with MEPC.312(74) and relevant MARPOL regulations.

  2. Shipowners and Ship Managers

    Shipowners and ship managers are required to notify the Administration of the intention to use ERBs onboard Cook Islands flagged vessels. The Administration has to be provided with the vessel name and IMO number as well as with the ERB software details and estimated date of installation.

    The use of ERBs onboard has to be approved by the Administration for every single vessel. The Administration will also make sure that a “Declaration of Marpol Electronic Record Book” (according to MEPC.312(74) Para. 5) is issued to the vessel by either the Administration or by the RO issuing relevant MARPOL certificates on behalf of the Cook Islands.

The above is applicable to the following books:

  • Oil Record Book, parts I and II (MARPOL Annex I, regulations 17.1 and 36.1);

  • Cargo Record Book (MARPOL Annex II, regulation 15.1);

  • Garbage Record Book, parts I and II (MARPOL Annex V, regulation 10.3)

  • Ozone-depleting Substances Record Book (MARPOL Annex VI, regulation 12.6)

  • recording of the tier and on/off status of marine diesel engines (MARPOL Annex VI, regulation 13.5.3)

  • Record of Fuel Oil Changeover (MARPOL Annex VI, regulation 14.6);

  • Record Book of Engine Parameters (NOX Technical Code, paragraph 6.2.2.7)

For further information, refer to attached file “MCI_225_2020_Electronic_Record”.

OSV Chemical Code

(Circular 196/2019)

The Code for the Transport and Handling of Hazardous and Noxious Liquid Substances in Bulk on Offshore Support Vessels (OSV Chemical Code), entered into force on a voluntary basis on 1st July 2018 (IMO Resolution A.1122(30).

The OSV Chemical Code supersedes IMO Resolution A.673(16), (LHNS Guidelines), which may continue to apply to OSVs constructed (i.e. keel lay date) on or after 19 April 1990 and before 1 July 2018.

However, existing OSVs, constructed on or after 19 April 1990 and before 1 July 2018, may now be permitted to carry products that are assigned for carriage on a type 2 ship in the IBC Code, provided that they comply with the OSV Chemical Code, except for the stability provisions in chapter 2 of the Code, and subject to the satisfaction of the Administration.

The Administration delegates to Recognised Organisation (RO) all surveys and verifications relevant to the OSV Chemical Code.

For further information, refer to attached file “Circular 196-2019”.

Exemptions for Unmanned Non-Self-Propelled (UNSP) barges

(Circular 272/2022)

When Owners or Managers of UNSP barges wish to apply for exemptions from MARPOL survey and certification requirements, the following procedure applies:

  • Owners/managers to get in touch with Recognised Organisation (RO)

  • Recognised Organisation (RO) will review the necessary drawings as per MEPC.1/Circ.892

  • Upon satisfactory review of the drawings, Recognised Organisation (RO) will carry out the relevant survey as per MEPC.1/Circ.892;

  • Upon satisfactory results of the survey, Recognised Organisation (RO) will notify the Administration accordingly and the Administration will issue the exemption certificate valid for a period not exceeding five years.

BWM Convention

Approval of BWM Systems

(Circular 221/2020 and Circular 263/2022)

The BWM 2004 Convention (Reg. D-3.1) requires that ballast water management systems (BWMS), complying with Reg. D-2, must be approved by the Administration according to the guidelines developed by the Organization.

The approval shall take the form of a Type Approval Certificate of BWMS, according to Paragraph 6 of the Guidelines G8 - MEPC.279(70) or BWMS Code - MEPC.300(72), whichever is applicable.

For BWMS to be installed on board a Cook Islands flagged vessels, there are two options:

  • Type Approval issued by the Administration:

    Manufacturers shall submit the type approval request to one of the IACS Recognized Organization, that at the end of the approval process will issue a Type Approval Certificate of BWMS on behalf of the Cook Islands Administration.

  • Type Approval issued by another Administration, under Res. MEPC.279(70) – G8 – or MEPC. 300(72) – BWMS Code:

    Manufacturers shall submit a copy of the Type Approval Certificate together with the type-approval report according to Part 7.2 of the Annex of either Guidelines G8 or BWMS Code, which ever is applicable. The Administration will issue a Type Approval Certificate on a case by case basis, based on the approval already carried out by the other Administration, with the same validity of the certificate the approval was based.

Further, for BWMS type approved by another Administration under Res. MEPC.174(58) - that can be installed on board until the 28th October 2020 - Manufacturers shall submit copy of the Type Approval Certificate together with a type-approval report complying as much as possible with Part 7.2 of the Annex of the BWMS Code. The Administration’s approval will be conveyed through the issuance of the International Ballast Water Management Certificate.

For further information, refer to the attached files “Circular 221-2020.pdf” and “Circular 263-2022.pdf”.

Electronic Ballast Water Record Book

(Circular 323/2025)

From 1 October 2025, electronic BWRBs may be used provided that the following requirements are met:

  1. The electronic BWRB is approved in accordance with IMO Resolution MEPC.372(80) (Guidelines for the use of Electronic Record Books under the BWM Convention).

  2. A ship-specific Declaration is carried on board, issued either by the Administration or by Recognised Organisation (RO), confirming compliance of the installation with IMO guidelines.

TONNAGE 69

Untitled

Miscellaneous technical requirements

Ships of less than 500 GRT

The Cook Islands forms for this size vessels are:

  1. Survey form 12A: Survey report Cargo Ship Safety Equipment, which is in the attached file “SurveyForm12ACargoShipSafetyEquipment-v4” and

  2. Record 7A: Record of Equipment for the Vessel Safety Certificate, which is in the attached file “Record7A_VSSrecord-v4”.

Alternatively, Cook Island applies IACS Recommendation 99, provided that it is less than 500 GT.

Hong Kong Convention

(Circular 307/2024)

The Cook Islands are not yet signatories to the Convention. Consequently, Owners have the option to request Recognised Organisation (RO) to issue a Statement of Compliance for the Inventory of Hazardous Materials. This statement is provided upon completion of the initial survey.

ISM Code

Authorization & Instructions

Audit and ship type accreditation
Ship typePSPHPRBCOTCTGCCHCSMO

Document of Compliance

InterimXXXXXXXXXX
InitialXXXXXXXXXX
PeriodicalXXXXXXXXXX
AdditionalXXXXXXXXXX
RenewalXXXXXXXXXX

Safety Management Certificate

InterimXXXXXXXXXX
InitialXXXXXXXXXX
IntermediateXXXXXXXXXX
AdditionalXXXXXXXXXX
RenewalXXXXXXXXXX

Note:

A notification should be sent to the Administration before any Interim, Initial, Intermediate, Annual (Periodical), Renewal ISM audit (SMC and DOC)

Requirements of the Administration
Requirements of the AdministrationAction by
Full term certificates to be issued by Recognised Organisation (RO)MOC / auditor
Reference documents

Amendment of agreement dated 18/03/2012 grant to Recognised Organisation (RO) the Full authorization

Specific Requirements

Cyber Security to be included in SMS

(Circular 242/2020)

The Admnistration recommends all DOC holders to revise their SMS taking into account the IMO Guidelines assessing their SMS’s effectiveness for handling cyber security and develop appropriate measures.

The Maritime Cyber Risk Management shall be included in Companies’ Safety Management Systems within the first annual verification of the DOC after 1st January 2021.

For further information, refer to the attached file “MCI-Circular_242-Cyber-Security-.pdf”.

ISPS Code

Authorization & Instructions

SSP approval / reviewShip auditISSC issuance
YesYesYes

Observation(s):

Full authorization granted - amendment dated 18/03/2012 (refer to document attached)

A notification should be sent to the Administration before any Interim, Initial, Intermediate, Renewal ISPS audit

ItemSpecific requirementsObservation(s)
Document of referenceAmendment of agreement dated 18/03/12 (Full authorization)

MLC, 2006

Scope of authorisation

DMLC II
 YesNoObservation
Approval of DMLC IIX  
Inspection & Certification
 InspectionCertification
YesNo
Full recognition (Recognised Organisation (RO) is RO)XX 

A notification should be sent to the Administration before any Interim, Initial, Intermediate, Renewal MLC inspection

Specific Flag Requirements

MLC Implementation

Refer to Circular 276/2023

The Administration requires that all vessels to which MLC applies, shall be fully inspected by Maritime Cook Islands or by an approved Recognised Organisation, to verify compliance with MLC requirements.

The following types of vessels should be following the process detailed in Circular 276/2023:

  1. Commercial and Dual registered yachts equal or over 500 GT

  2. Passenger vessels regardless of their GT

  3. All other vessels equal or over 200 GT, ordinarily engaged in commercial activities

Recognised Organisation (RO) can issue a MLC Certificate on behalf of the Administration (Refer to Circular 276/2023).

Upon satisfactory completion of each inspection, an inspection report will be issued to the vessel by either Administration or by an approved Recognised Organisation and it shall be kept onboard at all times. Each inspection report should be kept onboard for the entire MLC Cycle (5 years).

Every vessel to which MLC and the Circular 276/2023 apply, irrespective of type and size, shall submit to the Administration a completed declaration of the individual or entity that assumes the responsibility of the ‘shipowner’ under the MLC.

(Circular 57/2012 in attached file “mci-circular-57-maritime-labour-convention-implementation”)

Refer to Circular 293/2024

For all vessels subject to Inspection and Certification, the new DMLC I will be issued by the Administration within 3 months before the first mandatory MLC inspection (Initial, Intermediate, Renewal) and sent to the Owners and, where applicable, to Recognised Organisation (RO), along with the DMLC II, editable, to be updated and amended.

MLC Shipowners are required to submit to the Administration and, where applicable, to Recognised Organisation (RO) the DMLC II, duly filled, within 30 days before the first mandatory MLC Inspection.

The new DMLC II, duly filled, will be checked through a dedicated checklist by the Administration, or through Recognised Organisation (RO) specific procedures, during the first mandatory MLC inspection.

Appendix — Agreement governing the delegation of statutory certification services

Agreement

See the attached files:

  • “Agreement_CookIslands_RO_29042016”.

  • “Amendment_RO_Cook Islands_01012017”

Appendix — Annex 1 to the Agreement

Applicable instrument and degree of authorization

See the attached file “Annex1_CookIslands_RO_29042016”.

Refer also to the amendment to the agreement, dated 18/03/2012 and related to the ISM and ISPS delegations, in the attached file “CY05_NOTICE BY THE REGISTRAR_18.03.12”.

Appendix — Annex 2 to the agreement

Reporting to the Administration

See the attached file “Annex2_CookIslands_RO_29042016”.