Korea - Specific requirements by the Korean Administration

Korea

Flag instructions relating to statutory surveys

Flag procedural requirements

Standing requirements
Standing requirementsAction by
1- Reporting on entry into classRecognised Organisation (RO) Korea
2- Reporting on requests for exemptions or interpretationsRecognised Organisation (RO) Korea
3- Reporting on cases of major deficiencies, as per IACS Recommendation No. 98 (Duties of surveyors under statutory conventions and codes)Recognised Organisation (RO) Korea
4- Pre-authorisation prior to extending statutory certificatesRecognised Organisation (RO) Korea
5- Pre-authorisation prior to issuing conditional certificatesRecognised Organisation (RO) Korea
6- Reporting on detentionsRecognised Organisation (RO) Korea
7- Submission of copies of statutory certificatesRecognised Organisation (RO) Korea
8- Reporting on class suspension or class modificationRecognised Organisation (RO) Korea
9- Reporting on class withdrawalRecognised Organisation (RO) Korea
10- Reporting on issuance and amendments of Recognised Organisation (RO) Classification RulesRecognised Organisation (RO) Korea
11- Reporting to the Administration according to RO agreement Annex 2Recognised Organisation (RO) Korea

General policy

Single contact point

All correspondence between MOF and Recognised Organisation (RO) M&O shall be channelled through Recognised Organisation (RO) Korea.

The local Recognised Organisation (RO) organization of Statutory & Classification Affairs for Flag Administration (Korea) is as follows:

graph1
Marine & Offshore Chief Executive to KOREA
  • Shall be the general manager responsible for the carrying out the statutory certification and services on behalf of the Korean government.

  • Tel: +82 (0)51 640 2710

Marine Customer Centre KOREA (MCC KOREA)
Korean Plan Office (KPO)
  • Technical support for the Classification / Statutory regulations / Local Acts to KOREA

  • Tel: +82 (0)51 640 2721 / 2722 / 2723

  • Email: bvkpo_mail@VERITAS (bvkpo.mail@bureauveritas.com)

Ship in Service (NS)
Materials (RO)
New Construction (NC)

Agreement

Untitled

An Agreement has been signed between the Ministry of Oceans and Fisheries of the Republic of Korea (MOF) and Recognised Organisation (RO) SA on 21st June 2023.

The Agreement and its Appendices 1and 2 show the details of authorization granted (see Agreement governing the delegation of statutory certification services of ships to Appendix 2 to the Agreement).

Recognised Organisation (RO) M&O, on behalf of the government of Republic of Korea, shall perform statutory surveys and issue the relevant certificates to ships registered in the Republic of Korea.

Untitled

An Agreement has been signed between the Korean Coast Guard (KCG) and Recognised Organisation (RO) on 31st December 2019 (see AGREEMENT GOVERNING THE DELEGATION FOR THE APPROVAL OF MARINE POLLUTION PREVENTION PLAN OF SHIP (SOPEP AND SMPEP).) which has been extended for five years until 31st December 2029.Recognised Organisation (RO), on behalf of the government of Republic of Korea, shall perform review and approve to marine pollution prevention plan (SOPEP and SMPEP) to ships registered in the Republic of Korea.

MOF information

Additional information may be found on following website:

www.mof.go.kr/en/index.do

Interpretations, Equivalents and Exemptions

Recognised Organisation (RO) shall apply the IMO Interpretations and Circulars, as well as available IACS Unified Interpretations, unless provided with written instruction to apply a different interpretation by the Administration.

Recognised Organisation (RO) shall obtain prior approval from the Administration before waiving or exempting any application of the Relevant Laws.

Exemption certificates shall be approved only by the Administration.

Issuance of Conditional certificates

Conditional certificates shall be approved only by the Administration.

Reporting

If the condition of a ship is deemed to be such that the ship is not fit to proceed to sea without danger to the ship or persons on-board or causing unreasonable threat to the marine environment or to the third parties, Recognised Organisation (RO) shall immediately notify such fact to the Administration. In this case, the notice shall include the names of the ship, ship owner, official number, and the detailed contents regarding the significant deficiencies or the violations of the relevant Laws by the Korean ship or ship owner.

If and when a ship, that has received a certificate pursuant to the terms of this Agreement, violates any of the relevant Laws, but the ship owner does not take any remedial measures, then Recognised Organisation (RO) shall immediately notify such matters to the Administration.

In the event that there are reasons whereby Recognised Organisation (RO) cannot carry out its services specified in the Agreement, Recognised Organisation (RO) shall immediately notify the Administration of the fact.

Reporting by Recognised Organisation (RO) Korea

Regarding reporting by Recognised Organisation (RO) Korea to the Administration, refer to Appendix 2 (Appendix 2 to the Agreement).

Reporting of accidents to the Ministry of Oceans and Fisheries

In the event of a maritime accident, such as listed below, in addition to the attached file (A6.11 Ship accident record), the master's statement of accident, evidence photos, and other relevant information are to be sent to MCC_PUSAN at kor_cpu@bureauveritas.com:

  • Collision (between ships)

  • Grounding (ship get stuck on reefs or shallow waters)

  • Sinking (submerged ship)

  • Fire (any fire on a ship)

  • Explosion (any explosion on a ship)

  • Machinery failure (engine and mechanical equipment failure with ship unable to manoeuvre)

  • Loss of life (death or injury of a crew member or occupant on a ship)

  • Any accident in which a passenger of a passenger ship is injured, or the operation is delayed due to a failure or abnormality in the engine/equipment.

Definitions

Ship Type
Ship TypeCategory 1 shipsCategory 2 shipsCategory 3 shipsCategory 4 ships
Passengers ShipsInternationalX   
Non-international X  
Non Passenger ShipsInternationalGT >= 500  X 
GT < 500   X
Non-international   X
“Age of ship”

SOLAS reg.I/2 - (Article 2.1 of the Enforcement Decree of the Ship Safety Act / R.O. Korea)

"Age of a ship" means the elapsed period of time determined from the dated of launch of the ship.

“Type of vessel”

The marking of the purpose of the vessel to be marked on the Ship Survey Certificate according to the Ship Safety Act (see Type of Vessel _ Ship Survey Certificate (Korean & English)).

Qualification of Surveyor

More than 3years experience

Even if who is a qualified surveyor according to the Recognised Organisation (RO) Qualification Scheme, The Korean Flag vessel surveys should be surveyed by the surveyor with at least three (3) years of ship survey experience. (Article 97 of the Enforcement Decree of the Ship Safety Act / R.O. Korea)

Electronic certificates

(Notice No. 2020-179)

Recognised Organisation (RO) is authorized to issue certificates in an electronic format according to FAL.5/Circ.39/Rev.2 from 18 December 2020.

For further information refer o the attached file “Notice on the issuance of Electronic certificates of ships _ MOF Notice No 2020-179”.

Survey by remote method

(Refer to MOF Notice MITD-607, see Guidelines for Ship Survey by Remote Method (Korean & English))

The MOF allows a remote survey method (i.e. a ship inspection performed by indirect means such as photographs, written materials, video calls, videos, etc. without a surveyor being present on the ship) for the following items:

In accordance with the Ship Safety Act:

  • Continuous Survey of Machinery.

  • Occasional survey for extension of propeller shaft and stern tube extraction period and for extension of boiler survey period.

  • Occasional survey for the request for lay-up survey, extension of lay-up period and lay-up release.

  • Occasional survey for issuance of Temporary Alteration Certificate.

  • Underwater survey.

  • Temporary Navigation Survey for yachts imported from Japan, of less than 20 gross tons and less than 24 meters in length, with a navigation area within coastal area. (Checklist Annex 2 of MITD-607 should be used.)

In accordance with the Ship Safety Act, Marine Environment Management Act, and Ballast Water Management Act:

  • Occasional survey for supplementation or repair of ship facilities, etc.

  • Occasional survey to check correction of recommendations regarding ship facilities, etc.

  • Occasional survey for postponement of surveys.

  • Some items of periodic surveys (excluding registration survey or additional survey items of renewal survey).

An any other survey items deemed necessary by the MOF.

Remote survey shall be double verified by another surveyor other than the surveyor in charge after being performed.

Recognised Organisation (RO) shall notify the MOF of the results of the remote survey.

Overdue statutory surveys

Whenever a surveyor is requested to carry out a mandatory (annual / periodical / intermediate) statutory survey which is overdue (i.e., a survey falling outside the “window”), the surveyor immediately advises Ministry of Oceans and Fisheries (MOF) through Recognised Organisation (RO) Korea (MCC_PUSAN at kor_cpu@bureauveritas.com) before carrying the requested survey.MOF will then review the case and after taking into consideration a number of factors, including but not limited to, the type, size and age of ship, history of ship, scope of overdue survey and time survey has been allowed to elapse, will advise the surveyor as to the extent of survey to be carried out.Each notification will be dealt with on a case-by-case basis.After the required surveys have been satisfactorily carried out, the surveyor signs and stamps the relevant endorsement.

Change of flag

Surveys

No ship should be allowed to operate with any outstanding statutory recommendation(s). In case where it is deemed that a deviation from this policy is warranted, it should be invariably referred by Recognised Organisation (RO) to the Administration for consideration and issue of the appropriate instruction.

In cases where the change of flag occurs outside the statutory time window, the surveys shall be limited in scope to the extent of the applicable annual survey with the exception of SOLAS Safety Radio, SOLAS Safety Equipment and MARPOL Annex IV surveys that shall be carried out to the scope of renewal survey.

In the case where the change of flag occurs within the statutory time window, then appropriate surveys to the scope of renewal / intermediate / periodical / annual shall be carried out. If the renewal surveys are due, then these should be conducted to the extent possible.

The statutory survey reports for the change of flag surveys shall be made available the soonest possible to the Administration either in hard copy, by email, or through access to the Recognised Organisation (RO) database.

Documents

In the case of a vessel whose previous flag is an IMO ratifying flag state, and which has maintained its certificates in compliance with international regulations, the validity of previous surveys and certificates can be recognized.However, the following must be additionally reviewed based on Korean ships laws and acts, and is delegated to the Recognised Organisation (RO) Korean Plan Approval Office (KPO):

  • Lifesaving appliances

  • Firefighting equipment/systems

  • Accommodation/Habitability

  • Sanitary system

  • Navigation system

The following drawings and documents should be submitted to the Recognised Organisation (RO) Korean Plan Approval Office (KPO) to be reviewed whether it meets the Korean ships laws and acts:

  • General arrangement

  • Crew accommodation plan

  • Navigation equipment arrangement including specification of facilities

  • Life Saving Plan

  • Fire control plan and booklet (Korean + English)

  • Cargo Securing Manual (Korean + English)

  • SOPEP (Shipboard Oil Pollution Emergency Plan) (Korean + English)

  • SMPEP (Shipboard Marine Pollution Emergency Plan) (Korean + English)

  • P&A Manual (Korean + English)

  • BWMP (Ballast Water Management Plan)

  • Other documents as deemed necessary by KPO

If SOPEP, SMPEP, P&A Manual, and Cargo Securing Manual approved by the previous administration or copies of manuals submitted for approval has been provided onboard, the observation (verification scheme 1) to review and approve them may be imposed for up to two (2) months: for this reason, short-term certificates are not issued.

Postponement of renewal surveys and extension of the Ship Survey Certificate

Postponement of the renewal survey and extension of the Ship Survey Certificate will be considered by the Administration only in cases where circumstances so warrant and after Recognised Organisation (RO) has recommended such a postponement.

According to the Korea Ship Safety Act, the following extension of the Ship Survey Certificate can only be allowed under specific conditions, and prior required approval from the Ministry of Oceans and Fisheries (MOF) (Refer Article 6 of the Enforcement decree of the Ship Safety Act - President Decree):

  1. within three months: where the relevant ship is located where it is impracticable to undergo a special survey* or an international convention survey prescribed by Ordinance of the Ministry of Oceans and Fisheries.

  2. within five months: where the relevant ship underwent a special survey* or an international convention survey prescribed by Ordinance of the Ministry of Oceans and Fisheries in a foreign country, but a ground arises making it impossible to keep the ship survey certificate or the international convention certificate in the ship.

  3. one month: where the relevant ship is used for navigating a short distance (referring to a navigation distance, from a departure port to a final destination or round-trip to a departure port, which does not exceed one thousand nautical miles) (limited to an international Convention certificate).

If the above conditions are met, the application must be filled out and the relevant evidence document must be submitted together.

EU RO Mutual Recognition

The Korean Government is still maintaining the same position as those outlined in the letter, which was signed by nine(9) non-EU flag States and sent to the Vice President of the European Commission in November 2009 relating to Article 10 of EU Regulation 391/2009.

This means that the Korean Government will not accept the Mutual Recognition (MR) certificates for materials, equipment and components on board ships flying the Korean flag in the exercise of its exclusive jurisdiction, notably under the United Nations Convention on the Law of the Sea (UNCLOS). Meanwhile, it has also been confirmed that Korean Government does not have any imminent necessity to issue a written statement at the moment.

LL 66

Load Line Certificate

Recognised Organisation (RO) has full authorization.

Passenger Ships Stability - IS (Intact Stability) code 3.1.1.1

(Article 8 of the Ship Stability Standard / R,O,Korea)

Applicable to ships category 1 (see Ship Type)

A weight of passengers and crews shall be taken into account of their belongs inclusively as follow:

  • Crew and belongings: 120 kg/person,

  • Passenger and belongings: 110 kg/person

NB: Luggage weight in luggage store shall be taken into account additionally.

Handrails in Passenger Ships - ICLL reg.25 (3)

(Article 36.2 of Ship Equipment Standard / R.O.Korea)

Applicable to ships category 1 (see Ship Type)

In passenger ships, the opening of guard rail shall be not more than 230 mm. However, where safety device such as sailcloth or a net is provided, this is not applicable.

SOLAS 74

General

For extensions of validity period of certificates Recognised Organisation (RO) shall obtain prior approval from the Administration.

Postponement of Annual & Intermediate Survey - SOLAS reg.I/13

(Article 20 of the Enforcement Decree of the Ship Safety Act / R.O. Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Intermediate survey may be postponed if ship is on long voyage or fishing. Owner shall provide application for postponement (see attached file “SS-Form-7”, Application for postponement of intermediate surveys) to MOF including document mentioned voyage plan and ship's position.

Taking account into voyage plan, MOF may postpone intermediate survey until 12 months from due date of intermediate survey and shall inform owner of next due date of intermediate survey.

Postponed intermediate survey shall be completed without delay after ship arrive at port where to be surveyed.

In case Intermediate and Renewal survey overlap, renewal survey shall be completed.

In case category 1 and category 2 intermediate survey overlap, category I intermediate survey shall be completed. - category 1 intermediate survey: equivalent to Intermediate survey

- category 2 intermediate survey: equivalent to Annual survey

Cargo Ship Safety Construction Certificate

Recognised Organisation (RO) has full authorization, including for surveys in compliance with IMO Enhanced Survey Programme (ESP).

Recognised Organisation (RO) is authorized for approval of:

  • Stability Booklets

  • Loading Manual

  • Cargo Securing Manual

Requirements for Ro-Ro Passenger Ships - SOLAS reg.II-1/17-1

(Article 6 of the Standards on the Structure and Equipment etc. of Car Ferry Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

CCTV to monitor the whole area of ro-ro spaces shall be fitted. Monitor shall be located in wheel house.

Ro-Ro spaces in Ro-Ro Passenger Ships - SOLAS reg.II-1/17-1

(Article 24 of the Standards on the Structure and Equipment etc. of Car Ferry Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Electric power supplying cables and their use:

  1. enclosed ro-ro spaces carrying live-fish vehicles shall be provided with sufficient power supplying system to provide the electric power to the vehicles by reel lead cables of which at least same number of carrying vehicles. The power supplying system shall be provided that;

    1. electric power shall be automatically cut when overloaded,

    2. cables shall be of fire-resistance type.

  2. in case the live-fish vehicles are fitted with electrical oxygen generating unit, its electrical power shall be supplied from ship's electrical power system mentioned above during ship's operation without vehicles' power.

Hull thickness measurement - Korean government-approved companies and exceptional accreditation procedures.

(Article 31-3 of the Enforcement Decree of the Ship Safety Act / R.O. Korea)

For hull thickness measurement of all ships for which Ship Survey Certificates have been issued based on the Korea Ship Safety Act (ships with Korean nationality and BBC-HP contract applied), only the thickness measurement report conducted by the hull thickness measurement company approved by the Korean government (MOF) is accepted.If the ship is in a foreign country and there is no thickness measurement company approved by MOF, a foreign thickness measurement company may submit data according to the attached guidelines (A6.6 Accreditation procedure for Hull Thickness Measurement Company in outside of Korea) and obtain government approval before performing thickness measurement.

Lifting appliances

The requirements of SOLAS Chapter II-1 Regulation 3-13, do not apply to lifting appliances with a Safe Working Load (SWL) of less than 1,000 kg.

Lifting appliances with an SWL below 1,000 kg may be tested as part of the ship’s maintenance program under the Safety Management System.

Cargo Ship Safety Equipment Certificate

Recognised Organisation (RO) has full authorization.

Language in Drawings/Documents onboard - SOLAS reg.II-2/15.2.4

(Standards on the Construction of Fire Protection of Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Description of fire control plan and booklet shall be of bi-lingual written in Korean and English.

Fire protection, detection & extinction

Installation of Electrical Equipment in Closed Vehicle Deck for Passenger Ship - SOLAS reg.II-2/20.3.2.2

(Article 152 of the Standards on the Electrical Equipment of Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Installation of electrical equipment in closed vehicle deck for passenger ship, 450 mm specified in SOLAS Reg.20/3.2.2 is to be extended to 1000 mm.

Portable Fire-extinguishers in Ro-Ro Spaces - SOLAS reg.II-2/20.6.2

(Article 66 of the Standards on the Construction of Fire Protection of Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

At least 2 portable fire-extinguishers shall be provided in each ro-ro space or vehicle space.

Portable Fire-Extinguishers - MSC.1/Circ.1275

(Article 54 of the Standards on the Fire Protection Equipment of Ship / R.O.Korea)

In category 1 (see Ship Type) ships, portable fire extinguishers shall be provided to the space:

  • Public spaces and the spaces occupying 8 or more persons (except galley spaces): 1 (water, foam or dry powder fire extinguisher) per 200m2 of deck area or fraction thereof,

  • Steering gear room and fire control station: 1 (CO2 or dry power type - applicable for the category 1 ship of which gross tonnage 2000 ton or more only), 1 (water or foam type) and 1 (foam, CO2 or dry powder type)

Fixed CO2 Fire Extinguishing System - FSS Code Ch.5

(Article 13 of the Standards on the Fire Protection Equipment of Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Where compressed cylinders (pilot cylinders) are applied to open the CO2 storage bottles (including to use the CO2 storage bottles as the pilot cylinder), at least two cylinders shall be provided for the purpose, and controlled manually at local.

Live-saving appliances

Rotational Deployment of Marine Evacuation System - SOLAS reg.III/20.8.2

(Appended table 14 - II.1 of the Standards on the Life-Saving Equipment of Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

MES shall be dropped into water and deployed by remote or manual operation (whichever fitted on board) at least once every six year. Where one or more MES are provided on a ship, each system shall be deployed a rotational basis at six year interval.

MES shall be inflated fully within 3 minutes, internal pressure of chamber shall be within design pressure on the manufacturer's instruction.

In case this is impracticable due to ship's position, weather/sea condition or other working condition and accepted by MOF, that may not applicable.

Periodical Servicing of Hydrostatic Release Units - SOLAS reg.III/20.9

(Appended table 14 - I.10 of the Standards on the Life-Saving Equipment of Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

  1. There shall be no external damage (corrosion, rust or sticking, etc.).

  2. Hydrostatic release units shall be operated at pressure of setting depth of water on following condition;

    • Hook - load(5Kg or 200Kg)

    • Diaphragm- pressure equivalent to depth of water (pressure correspond to 2~4 meter depth of water)

    However, in case of disposable hydrostatic release units with the period of validity, operational test can be omitted.

  3. According to b), in case it does not operated at the first trial, the hydrostatic release units shall not be reused.

Retention for Record of Servicing of Liferaft - Res.A.761(18), 5.15

(Appended table 14 - I.18 of the Standards on the Life-Saving Equipment of Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Service supplier should be kept a record of servicing with following pictures for at least 5 years after the date of service and provide them upon owner's request;

  1. Following main process

    • Overall inflated condition (including ship's name) after charging cylinder

    • Launched condition by launching davit if applicable

    • Measurement of weight for CO2 cylinder

    • Other condition of non-conformity for main components or etc.

  2. Condition of stowage (including hydrostatic release units) according to Annex 14, 17.b(Liferaft to be fitted on board and fitting condition for painter system, lashing band or hydrostatic release units, etc. to be verified)

Stowage of MES - SOLAS reg.III/26

(Article 63.112 of the Standards on the Life-Saving Equipment of Ship / R.O.Korea)

Applicable to ships category 1 (see Ship Type)

For ro-ro passenger ships, embarkation arrangement shall be of either;

  1. in case the embarkation position is 5 m or more above the waterline in the lightest seagoing condition:

    1. at least one embarkation ladder on each side of ship, and

    2. at least two MES on each side of ship being capable of transferring the total number of persons from the ship to the liferafts within a period of 15 minutes.

  2. in case the embarkation position is between 2 m and 5 m above the waterline in the lightest seagoing condition, at least two net ladders on each side of ship or at least one embarkation ladder for each two launching appliances

Lifejackets and Immersion Suits for the Persons at Remote Located Area - SOLAS reg.III/3

(Article 87 of the Standards on the Life-Saving Equipment of Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Additional lifejackets and immersion suits for use at remotely located survival craft station (refer to reg.III/31.1.4) shall be provided at least same number of persons normally working at those locations at any time or total capacity of liferaft, whichever greater.

Service provider accreditation procedure

(Refer to attached file “Service provider accreditation_MSC Res 402(96)_MOF.pdf”)

Recognised Organisation (RO) confirms the qualification requirements of the service provider and requests approval from Ministry of Oceans and Fisheries (MOF) department. The MOF decides whether to accept or not the Recognised Organisation (RO) approved company, and registers the service provider's accreditation list (including models and types that can be maintained) on the homepage of MOF. For details on Government recognition procedure, refer to attached file “Service provider accreditation_MSC Res 402(96)_MOF.pdf”.

If the accredited service providers is not available (e.g. because manufacturer training cannot be completed (manufacturer closed, etc.), qualified companies cannot be used in the port of entry, etc.), the service provider that meet separate requirements as described in the Exception accreditation procedure and qualification requirements, are allowed. For details on Exception accreditation procedure, refer to attached file “Service provider accreditation_MSC Res 402(96)_MOF.pdf”.

Unavailability of new Emergency Position Indicating Radio Beacons - MSC.471(101)

(Refer to the Notice Advisory in Temporary guidance regarding unavailability of New EPIRB - MSC 471(101) (English))

Due to temporary market shortage and/or lack of availability of such new EPIRB, the Ministry of Oceans and Fisheries (MOF) accepts that:

  • Existing IMO Resolution A.810(19) compliant EPIRBs installed before 01 July 2022 may continue to be used until such time as they can no longer be maintained.

  • If an IMO Resolution MSC.471 (101) compliant EPIRB is unavailable for installation, an IMO Resolution A.810(19) compliant EPIRB may be installed or used until such a time an IMO Resolution MSC.471(101) compliant EPIRB becomes available or until 31 December 2024 whichever is earlier.

Cargo Ship Safety Radio Certificate

Recognised Organisation (RO) has full authorization.

Installation of DGPS - SOLAS reg.V/19.2.1.6

(Article 108.2 of the Standards on the Life-Saving Equipment of Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

A receiver for DGPS (Differential Global Positioning System) is to be provided in addition to requirement of SOLAS Reg.V/19.2.1.6.

Minimum number of persons with required qualifications to operate the radio installations

(Article 22-2 of the Enforcement Decree of the Korea Ship Officers Act)

At least three persons who meet the minimum qualifications to operate the radio installations are required when a deck officer intends to concurrently take charge of additional duties of a radio operator. 

Therefore, the minimum number of persons with required qualifications to operate the radio installations (Form R) is three (one GOC + two ROC).

Passenger Ship Safety Certificate

Recognised Organisation (RO) has full authorization.

Carriage of cargoes and oil fuels

Manuals/Documents to be Written in Korean - SOLAS reg.VI/5

(Article 4 of the Standards on the Cargo Loading and Securing / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Cargo securing manual shall be drawn up of bi-lingual written in Korean and English.

Manuals/Documents to be Written in Korean - SOLAS reg.VI/7.2

(Article 12 of the Standards on the Cargo Loading and Securing / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Booklet to enable the master to prevent excessive stresses in the ship's structure required by the regulation shall be of bi-lingual written in Korean and English.

IP Code and SOLAS Chapter XV

Scope of application

A ship (hereinafter referred to as a “ship”), that is not a passenger ship that intends to transport more than 12 non-seafarers, including industrial personnel, shall be inspected in accordance with international safety standards (hereinafter referred to as “safety standards”) for ships carrying industrial personnel adopted by the International Maritime Organization.

Notwithstanding the above, if it is difficult to apply safety standards to the following vessels:

  • Ships used for domestic navigation,

  • Vessels of less than 500 gross tonnage used for international navigation,

it may be carried out by the Minister of Oceans and Fisheries

Requirements for industrial personnel recognition

Marine industrial activities refer to the construction, maintenance, decommissioning, operation or servicing of marine facilities related to the renewable or hydrocarbon energy sector, aquaculture, resource exploration and development by marine mining or similar activities.

An industrial personnel means a person who is transported or accommodated by ship for the purpose of above marine industrial activities, which is carried out on other ships and/or maritime facilities, and who has completed an industrial personnel safety curriculum or similar training (basic safety training of the Global Wind Organization (GWO), basic safety training of Offshore Petroleum Industry Training Organization (OPITO)) operated by the Korea Institute of Maritime and Fisheries Technology amongst other.

In such cases, the educational (training) certificate shall be in a valid state, and if there is a medical certificate issued pursuant to Article 87 of the Seafarers Act or a notification of the results of a medical examination under Article 52 of the National Health Insurance Act, amongst other, the physical and medical suitability shall be deemed to be satisfied.

Industrial Personnel Safety Certificate

An Industrial Personnel Safety Certificate must be issued, based on survey dates, in accordance with SOLAS Regulation XV/3.2 and XV/3.3.

MARPOL 73/78

General

For extensions of validity period for certificates Recognised Organisation (RO) shall obtain prior approval from the Administration.

Annex I. IOPP certificate

Regulations for the prevention of pollution by oil

Recognised Organisation (RO) has full authorization and is authorized to approve ship-to-ship (STS) oil transfer Plan.

Manuals/Documents to be Written in Korean - MARPOL Annex I/reg.37

(The Enforcement Decree for the Prevention of Pollution from Ships / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

SOPEP/SMPEP shall be prepared with bi-lingua written in Korean and English.

Annex II. NLS certificate

Regulations for the control of pollution by Noxious Liquid Substances in bulk

Recognised Organisation (RO) has full authorization and is authorized to approve the Procedures & Arrangements (P&A) Manual.

Manuals/Documents to be Written in Korean - MARPOL Annex II/reg.14

(The Enforcement Decree for the Prevention of Pollution from Ships / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Text in P&A manual shall be of bi-lingua written in Korean and English.

Annex IV. ISPP certificate

Regulations for the prevention of pollution by sewage from ships

Recognised Organisation (RO) has full authorization.

Annex V

Regulations for the prevention of pollution by garbage from ships

Recognised Organisation (RO) has full authorization.

Annex VI. IAPP, EIAPP and IEE certificates

Regulations for the prevention of air pollution from ships

Recognised Organisation (RO) has full authorization including for surveys of oil vapour emission control system.

Recognised Organisation (RO) is authorized to approve the Volatile Organic Compounds (VOC) Management Plan.

Discharge of nitrogen oxide

With respect to the air pollution prevention, in appointing surveyors for surveying the facilities for prevention of discharge of nitrogen oxide from diesel engine, Recognised Organisation (RO) shall make a prior enquiry with the Minister of Environment of Korea.

EEDI Application when Freeboard Changes - MARPOL Annex VI/reg.20.1

(Article 30.2 of the Enforcement Decree for the Prevention of Pollution from Ships / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Major conversion includes the increase of assigned freeboard.

Tonnage 69

Tonnage certificate

Recognised Organisation (RO) is authorized on a case by case basis, upon request of the Chief of Regional Office of the Oceans and Fisheries or a consul of Korea.

AFS

Anti Fouling Convention

Recognised Organisation (RO) has full authorization.

BWM

Ballast Water Management Convention

Recognised Organisation (RO) has full authorization, including approval of Ballast Water Management Plan.

Recognised Organisation (RO) is authorized to extend the validity period of certificates.

Recognised Organisation (RO) has “Certificate of Ship’s Ballast Water Management System Type Approval Testing laboratory (Readiness Evaluation)” designated by minister of Oceans and Fisheries. (See Certificate)

IOPP de-harmonization

(MOF Circular dated 03/01/2017)

The Administration has agreed shipowners to carry out advanced IOPP renewal survey. Prior agreement of the Administration is not requested.

The validity of the new IOPP certificate is to be 5 years from the survey completion date.

For further information, refer to attached file “BWM and IOPP DE_Harmonization _MOF_ KOREA”. (see BWM and IOPP DE _ Harmonization _ MOF _ KOREA).

Ballast Water Record Books (BWRB)

Each ship shall have on board either a Ballast Water Record Book (BWRB) or an Electronic Ballast Water Record Book (EBWRB). Surveyor should check that suitable entries are being made in the Record Book.

The BWRB entries are to be maintained on board the ship for a minimum of two (2) years after the last entry has been made and thereafter in the Company’s control for an additional minimum period of three (3) years. (Article 20, Paragraph 3 of the Enforcement Decree of the Ballast Water Management Act of R.O. Korea).

The technical requirements for EBWRB facilities and security, etc. must meet Resolution MEPC.370(80). If it is recognized that these requirements are met, a Declaration of the BMW Convention Electronic Record Book can be issued. (see Attached Declaration of the BMW Convention Electronic Record Book in Application and Declaration of BWM Convention Electronic Record Book)

The owner of the ship who intends to use the EBWRB must obtain a Declaration of the BMW Convention Electronic Record Book for each vessel.

Miscellaneous Technical requirements

Noise Code

Qualification of Noise Measurement - Noise code 3.2

(Article 947 of the Standards on the Structure of Steel Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

The person conducting measurements shall have either;

  1. minimum one year of experience of ship's noise measurement holding a license of "engineer noise & vibration" or "industrial engineer noise & vibration" by the code of national technical qualification act,

  2. minimum two years of experience of ship's noise measurement from an institute for which certified according to ISO 17020/25, or

  3. minimum two years of experience of ship's noise measurement after completion of education from a special institution or educational institution regarding noise and sound accredited by MOF.

Verification of measuring instruments and calibrators - Noise code 3.8

(Article 946 of the Standards on the Structure of Steel Ship / R.O.Korea) Applicable to ships category 1 and 3 (see 1.2.7.1)

Instruments and calibrators must be verified at least annually by an accredited institution in accordance with the national standard testing laboratory or technical standard (ISO 17025(2005) cor 1:2006).

ESP Code

ESP guideline Annex B Part A 1.1.1

Applicable to ships category 1 and 3 (see Ship Type)

Annex 1 Scope of Application ESP according to type of ship

  1. The guideline shall apply all oil tanker.(Annex 1–2.1 of the Standards on the Enhanced Survey for Ship / R.O.Korea)

  2. The guideline shall apply ship having structure to enable to carry liquid dangerous cargo in bulk except liquefied gas carrier.(Article 2 of the Enforcement Decree of the Ship Safety Act, Article 1 of the Standards on the Enhanced Survey for Ship / R.O. Korea)

The guideline shall apply to above ship having integral tank. Where ship have two type of tank (integral and independent tank), the guideline should apply to only cargo length area for integral tank. Gas Carrier and combination ship (ship having structure to enable to carry liquid dangerous cargo in bulk) having independent tank shall apply to survey of gas carrier.(Annex 1 – 2.3 of the Standards on the Enhanced Survey for Ship / R.O.Korea)

Others

Size of Bed in Passenger Room

(Article 13 of Ship Equipment Standard / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Minimum size of a berth for passenger room shall be at least 200 cm by 90 cm.

Rotating machinery

(Article 9 of the Standards on the Electrical Equipment of Ship / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

The direction of the shaft of rotating machinery, among main electrical system, is to be line with the direction of bow and stern.

Installation Requirement of Explosion-proof Type Electrical Power Supply System in Closed Vehicle Deck

(Article 152 of the Standards on the Electrical Equipment of Ship / R.O.Korea)

Explosion-proof type electrical power supply system is to be installed for refrigerating vehicle in closed vehicle spaces.

Citadel

(Article 56.2 ~ 56.6 of Ship Equipment Standard / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

  1. Ship shall be provided with "citadel" where ship would be navigating in armed robbery attack area and/or in order to prevent piracy.

  2. The area of "citadel" shall be located within the area to be difficult to identify by pirates.

  3. The "citadel" shall be constructed of steel structure.

  4. Provisions and equipment in the "citadel": 1(one) two-way portable VHF radiotelephone apparatus, portable lantern (1(one) per person), 1 (one) portable fire extinguisher, Food rations (10000 kJ per person) and drinking water (3 liters per person), 1(one) First-aid kit, 1(one) portable toilet, Natural ventilation acceptable

  5. Satellite communication system consisting in followings shall be provided;

    • wired or wireless satellite communication device,

    • emergency battery chargeable in the area,

    • external antenna shall be fitted in the difficult place to identify

Spare Parts for Glasses for Sidelights

(Article 86 of Ship Equipment Standard / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Two (2) sets of glasses (red color, green color) for sidelights are to be provided as spare part.

Spare Parts for Machinery

(Article 187 of Ship Machinery Standard / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

Inventory and spare parts for the machinery engaging in ship's propulsion shall be provided onboard as per table 41 to 46. (refer to attached file “Spare_Parts_Machinery”). However, the number of machineries installed onboard is more than the required number of spare parts or inventories, the requirement would not be applicable.

Ship's Carving and Marking

(The Enforcement Decree of the Ship Act / R.O.Korea)

Applicable to ships category 1 and 3 (see Ship Type)

  1. The ship's name shall be marked on each of her bows and stern in visible area with letter of Korean (including Arabian figure) at least 10 cm height.

  2. The ship's port of registry shall be marked on hull in visible area with letter of Korean.

  3. Draft mark shall be marked on the hull on both sides above maximum water line in Arabian figure (10 cm height) at interval of 20 cm. The bottom of the figure shall be in line with the corresponding waterline.

  4. The marking shall be plainly visible and clear. The permanent marking referred above is changed/modified immediately where the information has been changed/modified.

e-Navigation Terminal

(Article 18 of the Act on Promotion of the Provision and Use of Intelligent Maritime Traffic Information Services / R.O. Korea)

Applicable to ships constructed or imported from abroad on or after 30 January 2021.

An e-Navigation terminal shall be installed on board all applicable ships.

The following ships are exempted from the requirements:

  • Ships under BBC-HP

  • Ships without a propulsion engine or mast.

  • Ships navigating or operating exclusively in inland waters

  • Ships of less than 3 gross tonnages, including fishing vessels

  • Ships not calling at Korean ports.

Additional documents/certificates to issue

Approval of drawings and documents

Drawings and documents reviewed and approved under the Act on Korean Ships shall mark the following:

  • Specified stamp

    graph2
  • Name of the surveyor responsible for approval

  • Approval date

New building

The following documents are available in attached files:

  • “Ship-Building (Special ship-building) Survey Certificate”.

    This document applies to all Korean Flag vessel and refers to Article 7.2 and 7.4 of the Ship Safety Act, Article 10.4 and 11.3 of the Enforcement Decree of the Ship Safety Act

    (refer to attached file “SS-Form-3”, in SS-Form 3 _ Ship-Building Survey Certificate)

  • “Temporary Navigation Certificate”

    This document concerns sea trail at ship delivery and refers to Article 11.2 of the Ship Safety Act, Article 22.2 of the Enforcement Decree of the Ship Safety Act.

    (refer to attached file “SS-Form-9”, in SS-Form 9 _ Temporary Navigation Certificate)

Ship in Service

The following documents are available in “Certificate Editor” and are to be issued as indicated below:

“Ship Survey Certificate”
  1. Depending of ship length and type, SS-Form5 or SS-Form6 (available in Certificate Editor) have to be issued after completion of surveys according to the Ship Safety Act.

    • SS-Form5 is applicable to length of ship less than 12 meters, except to the passenger ship and the ship of carriage of dangerous in bulk.

    • SS-Form6 is applicable to length of ship more than 12 meters, and to all the passenger ship and the ship of carriage of dangerous in bulk.

  2. Survey Codes

    • KSSR: Korean Ship Survey Renewal

    • KSSI: Korean Ship Survey Intermediate

    • KSSA: Korean Ship Survey Annual

    • KSSO: Korean Ship Survey Occasional

  3. Endorsement of certificate

    • International Conventional Vessel: The Surveyor shall sign the certificate after confirming that the ship has completed the relevant surveys such as the Load Line Convention, SOLAS Convention and related regulations. These are signed by the final confirmed surveyor.

    • Non-Conventional Vessel: The Surveyor shall sign the certificate after confirming that the ship has completed the requirements of the Korean Ship Safety Acts.

  4. Issue certificate

    • The issuance of this certificate shall take into account the requirements of the relevant Korean Ship Safety Act, and the MOF agreed to issue it by MCC_ PUSAN under the responsibility of the Chief Executive of the Recognised Organisation (RO) Korea, and seal must be sealed.

    • After completing the relevant surveys, the surveyor can issue a definitive limit Ship Survey Certificate valid for 5 months with the Recognised Organisation (RO) soft stamp. This is temporarily applied in consideration of not being able to use the seal stamp approved by the Ministry of Oceans and Fisheries in time. Therefore, the surveyor must forward a copy of the issued certificate to MCC_PUSAN and requested to issue a definitive certificate.

    • Contact to MCC_PUSAN: kor_cpu@bureauveritas.com

“Marine Pollution Prevention Certificate” and its Supplement
  1. These documents shall be issued after completion of surveys according to the enforcement decree for the prevention of pollution from ships.

    The above documents, confirming that the ship meet the requirement of Korean Ship Safety Act and the Enforcement decree for the prevention of pollution from ships, must be issued in addition to international certificates.

  2. Survey Codes

    • KPPR: Korean Pollution Prevention Renewal Survey

    • KPPI: Korean Pollution Prevention Intermediate Survey

    • KPPA: Korean Pollution Prevention Annual Survey

    • KPPO: Korean Pollution Prevention Occasional Survey

  3. Endorsement of certificate

    • International Convention Vessel: The Surveyor shall sign the certificate after confirming that the ship has completed the relevant surveys such as the MARPOL Convention and related regulations. These are signed by the final confirmed surveyor.

    • Non-Conventional Vessel: The Surveyor shall sign the certificate after confirming that the ship has completed to the requirements of the Enforcement Decree for the Prevention of Pollution from Ships.

    • Alternative: MARPOL Annex I, Annex II, Annex III, Annex V, Annex VI recognize international convention certificates and may only MARPOL Annex IV (Sewage) related matters to the MPP Certificate.

  4. Issue certificate

    • The issuance of this certificate shall take into account the requirements of the relevant Korean Marine Pollution Preventive Act, and the MOF agreed to issue it by MCC_ PUSAN under the responsibility of the Chief Executive of the Recognised Organisation (RO) Korea, and seal must be sealed.

    • After completing the relevant surveys, the surveyor can issue a definitive limit Marine Pollution Prevention Certificate valid for 5 months with the Recognised Organisation (RO) soft stamp. This is temporarily applied in consideration of not being able to use the seal stamp approved by the Ministry of Oceans and Fisheries in time. Therefore, the surveyor must forward a copy of the issued certificate to MCC-PUSAN and requested to issue a definitive certificate.

    • Contact to MCC_PUSAN: kor_cpu@bureauveritas.com

Checklists for non-convention ships

The following checklists are attached to this TNS and shall be filled when issuing:

Both above certificates are available in “Certificate Editor”.

Ship Recycling and IHM

Inventory of Hazardous Materials

(Refer to attached file “Letter-SOC_EU SRR_28 DEC 2020”)

(Refer to attached file “Letter-SOC_HKC_26 MARCH 2026”)

On request by the Shipowner or Master, a SoC may be issued by Recognised Organisation (RO) after verifying that the IHM, Part I meets the relevant requirements. Recognised Organisation (RO) may conduct this work irrespective of whether the vessel is classed by Recognised Organisation (RO) or not.

The following minimum requirements apply:

  1. the IHM must be ship-specific and take into account IMO Resolution MEPC.269(68). For an existing ship it must identify, at least, the hazardous materials listed in Appendix I of the Convention or Annex I of the EU SRR, as appropriate.

  2. A plan must be established by the ship describing the visual/sampling check by which the IHM is developed.

  3. Any laboratory used to carry out specific tests must take into consideration the guidance in MEPC. 269(68), Appendix 9.

  4. The IHM must be properly maintained and updated throughout the ship’s operational life. It must reflect the new installations that contain hazardous materials referred to in Appendix II of the Convention or Annex II of the SRR, as appropriate, and relevant changes in the ship’s structure and equipment, taking into account the exemptions and transitional arrangements applicable to those materials under international law.

  5. A SoC may be issued for the EU SRR to demonstrate meeting the requirements of Article 12 of regulation (EU) 1257/2013 on Ship Recycling.

  6. National legislation concerning ship recycling has not yet been enacted, with reference to Regulation 11 of the Hong Kong International Convention. A SoC demonstrating compliance with Regulation 11 of the Hong Kong Convention may be issued by Recognised Organisation (RO).

Survey of ships and of articles for ship use

Kind of surveys

All vessels are divided into general vessels and fishing vessels and are subject to the inspections in accordance with Ship Safety Act. The below instructions are to be applied for surveys in accordance with Ship Safety Act and Announcement of Ministry of Land, Transport and Maritime Affairs (MLTM, previously MOF) although Marine Environmental Management Act and Radio Regulation Law are commonly applied to the general vessels and the fishing vessels, and although vessels have their own surveys according to their applicable Conventions.

Kind of ship surveys according to Ship Safety Act:

  • Ship-building and After-building Survey according to Article 7 of Ship Safety Act

  • Special Survey according to Article 8 of Ship Safety Act

  • Intermediate Survey according to Article 9 of Ship Safety - Kind 1 Intermediate Survey - Kind 2 Intermediate Survey (Annual Survey)

  • Occasional Survey according to Article 10 of Ship Safety Act

  • Temporary Navigation Survey according to Article 11 of Ship Safety Act

  • International Convention Survey according to Article 12 of Ship Safety Act

  • Enhanced Survey (Tankers, etc...) according to Article 42 of Ship Safety Act

  • Towing Survey according to Article 43 of Ship Safety Act

  • Particular Survey according to Article 71 of Ship Safety Act

Type Approval and Examination according to Article 18 of Ship Safety Act

Survey of Articles for Ship Use according to Article 22 of Ship Safety Act

Ship-building Survey and After-building Survey (Article 7 of Ship Safety Act)

Scope of Ship-building survey

The ship builder shall take the ship-building survey from the commencement according to sub-para 1, 2, 4 ~ 6 and 14 of Article 4 of Enforcement Decree of Ship Safety Act about ship's facilities including the items about load lines in case of the ship prescribed with the Article 27 of Ship Safety Act. (Para.2 of Article 10 of Enforcement Decree of Ship Safety Act).

However, Survey based on the Korean Ship Safety Acts (include the other related acts for Korean ship) can only be performed on ships that have been registered by Recognised Organisation (RO) or being to be registered. (Para.2 of Article 60 of Ship Safety Act).Refer to Sub-para.1 (Hull), sub-para.2 (Machinery), sub-para.4 (Drainage facilities), sub-para.5 (Steering facilities), sub-para.6 (Mooring/Anchoring facilities), sub-para.14 (Electric facilities).

Scope of After-building survey

The ships that have not taken the ship-building survey (as the ships imported from abroad) shall take the after-building survey equivalent to ship-building survey according to the appended table No.1 of Enforcement Decree of Ship Safety Act prescribed about ship's facilities in above a) of 1). (Para.2 of Article 11 of Enforcement Decree of Ship Safety Act).

Issuance of Certificate

The ships being registered by Recognised Organisation (RO) shall take the survey during construction for ship-building survey and the survey after construction for after-building survey. The classification certificate shall be substituted by the ship-building certificate or the after-building survey certificate. (Para.3 of Article 10 of Enforcement Decree of Ship Safety Act).

Special Survey (Para.1 of Article 8 of Ship Safety Act)

Renewal Survey (RS) is an inspection which is to be carried out for ship's all facilities, equipment, load line and radio installations when a ship is put to service initially or when the Ship Survey Certificate for a ship, having the validity of 5 years, expires. In principle, RS is to be completed within three (3) months before the expiry date of the existing certificate. When a vessel having undergone the inspection by KOMSA (Korea Maritime Transportation Safety Authority) is transferred to Recognised Organisation (RO), the first RS shall be carried out by Recognised Organisation (RO). (Based on MOMAF letters "Inspection 91560-126" dated 16 April 1996 and "Fishing Vessel 53450-140 dated 7 November 1996) Preparation of survey is complied with the appended table No.10 of Enforcement Decree of Ship Safety Act.

Intermediate Survey (Para.1 of Article 9 of Ship Safety Act)

Intermediate survey (IS) is a simplified inspection which is to be carried out between RS and the next RS.

There are two kinds of IS: Kind 1 IS (Intermediate Survey) and Kind 2 IS (Annual Survey),

Survey items for Kind 1 Intermediate Survey (Kind 1 IS)

In Article 4 of Enforcement Decree of Ship Safety Act:

Sub-para.1 (Hull: docking or grounding/pulling-out of rudder and operating test for the closing appliances of water-tight door, fire door and etc./preparation according to 1.Nuo of the appended table No.10 of Enforcement Decree of Ship Safety Act in case of oil tankers, bulk carriers or ships carrying dangerous liquid substances in bulk) Sub-para.2 (Machinery: preparation according to 1.Na of the appended table No.11 of Enforcement Decree of Ship Safety Act) Sub-para.4 (Drainage facilities: preparation according to sub-para.3 of the appended table No.10 of Enforcement Decree of Ship Safety Act) Sub-para.5/6/7 (Steering Gear, Mooring and Anchoring facilities: arrangement of anchors and anchor chains), Sub-para.10/11 (Accommodations and Sanitary facilities: operating test or conditional test), Sub-para.12 (Navigational facilities: operating test and arrangement if portable), Sub-para.13/14 (Storage facilities and Cargo Gear for dangerous goods: operating test), Sub-para.15 (Electrical facilities: insulation resistance test and operating test), Sub-para.17 (Container facilities: conditional test), Sub-par.18 (Elevator: operating test), Sub-para.19 (Freezer, Refrigerator and Facilities for processing fishery product: operating test and conditional test). Operating test or Conditional test for load lines and radio installations.

Survey items for Kind 2 Intermediate Survey (Kind 2 IS - Annual Survey)

Installation of a scaffold for inspection of load lines marking. Operating test for closing appliances of water-tight door, fire door etc... In Article 4 of Enforcement Decree of Ship Safety Act: operating test or conditional test according to sub-para.2 (Machinery) / sub-para.4 (Drainage facilities) / sub-para.5 (Steering Gears) / sub-para.8 (Life saving appliances) / sub-para.9 (Fire extinguishing appliances) / sub-para.12 (Navigational facilities) and sub-para.13 (Stowage facilities for dangerous goods), conditional test according to sub-para.10 (Accommodation) and sub-para.11 (Sanitary facilities), insulation resistance test and operating test according to sub-para.15 (Electrical facilities). 1.Nuo (1) through (3) of the appended table 10 of Enforcement Decree of Ship Safety Act for cargo holds of bulk carriers over 10 years of age. Operating test and Conditional test for load lines and radio installations.

Kind and period of IS according to ship type

(Para.2 of Article 19 of Enforcement Decree of Ship Safety Act)

(a) Passenger ships, nuclear ships, underwater vehicles, high speed crafts, vessels other than fishing vessel of 24 meters and over in length, and 30 years or more in age: Kind 1 IS to be carried out within the time window (i.e. three(3) months before and after the anniversary date) of each anniversary date between two RS (Docking survey to be included). (see )

Anniversary dateyearyear + 1year + 2year + 3year + 4year + 5
Applied surveyRSKind 1 ISKind 1 ISKind 1 ISKind 1 ISRS
Beginning of certificate validity is the completion date of RS

(b) Vessels less than 24m in length in smooth waters only (except vessels of the above (a)) and fishing vessels less than 24 m in length, barges carrying the sand dredged, the floating marine structures and the sailing vessels less than 12m in length: Kind 1 IS to be carried out during the period between three (3) months before 2nd anniversary date after RS and three (3) months after the 3rd anniversary date after RS. (Docking survey to be included) (see )

Anniversary dateyearyear + 1year + 2year + 3year + 4year + 5
Applied surveyRSN/AKind 1 ISN/ARS
Beginning of certificate validity is the completion date of RS

(c) Vessels other than ships included in the above (a) and (b): Kind 1 IS or Kind 2 IS to be carried out within the time window of 2nd or 3rd anniversary date after RS. Hull bottom survey (Docking Survey) is to be carried out in conjunction with Kind 1 IS and the interval of any two docking surveys shall not exceed 3 years. (see )

Anniversary dateyearyear + 1year + 2year + 3year + 4year + 5
Applied surveyRSKind 2 ISKind 1 IS or Kind 2 ISKind 1 IS or Kind 2 ISKind 2 ISRS
Beginning of certificate validity is the completion date of RS

(d) Vessels exempted from Intermediate Survey (Para.3 of Article 19 of Enforcement Decree of Ship Safety Act):

  • Vessels less than 2 tons in GT

  • Vessels with no propulsion system and that sail only in still water service except the followings:

    • Vessels carrying passengers more than 13 persons;

    • Vessels carrying oil or waste (Refer to 1.Ga through La and 2.Na of the appended table No.1 of Enforcement Decree of Marine Pollution Prevention Act) in bulk according to Article 2 of Marine Environmental Management Act;

    • Vessels carrying the dangerous goods in bulk according to Article 41 of Ship Safety Act;

    • Pusher-barge combined with the vessels with the propulsion system;

    • Special vessels like submarine, etc... announced by the Minister of MLTM (previously MOF).

  • Vessels with no propulsion system or that do not carry passengers or cargoes in coastal service

  • Vessels having the licensed, permitted or reported fishery according to Article 6, 9 and 11 of Domestic Water Fishery Act.

Alleviation of preparing survey and submitting documents (Para. 5 & 6 of Article 31 of Enforcement Decree of Ship Safety Act)

Considering the structure, facilities, size, purpose or navigation area, the preparation of survey and submission of documents may be adjusted or exempted.The survey items from sub-paras.1.Na(1) to 1.Na.(6) out of the whole survey items of Kind 1 Intermediate Survey stipulated in para.1 of the appended table No.11 of Enforcement Decree of Ship Safety Act may be exempted for the vessels not less than 24m in length, and that are 30 years and older. However, the exemption may not be continued three times.Preparation of docking or grounding for special survey among preparations of Kind 1 Intermediate Survey may be exempted for the following vessels and preparations of para.1.Na through La among preparation for special survey may be exempted.However, the exemption may not be continued three times for passenger ships

  • Inland vessels

  • Vessels less than 15 years (except passenger ships)

Management of uninspected and laid-up vessels

Guidelines to report laid-up vessel

When ship’s operation are to be ceased for a certain period, the notice of ship's being laid-up is done by submitting “Statement for the Cause of Laying-up, issued by The Director of Regional Office of Oceans and Fisheries” (see SS-MOF-1 _ Statement of the Cause of laying-up) appended together with Ship Survey Certificate by Recognised Organisation (RO). The grace period of ship's survey is two (2) years and its extension may be granted for one (1) year at a time. In case that ships of gross tonnage 20 tons and over are intended to be laid up within the boarder of a port, the Confirmation on Report of Ship's Laying-up issued by the competent authority of the port of ship's registry according to Public Order in Open Port Act, Article 7, para.3 and its Enforcement Decree, Article 5, para.4 is to be submitted to Recognised Organisation (RO).

Laying-up survey

Once ship's owner submits “Statement for the Cause of Laying-up (SS-MOF-1)" (see SS-MOF-1 _ Statement of the Cause of laying-up) with Ship Survey Certificate (SS-Form 5 or SS-Form 6) to Recognised Organisation (RO), those documents are to be confirmed and then a Review Report shall be made.

Laying-up survey as a classification survey is to be dealt with according to Instructions for Classification Survey. Every laid-up ship shall be capable of transmitting and receiving distress alerts with radio installations on board.

Preserving ship survey certificate

While ship's being laid up, the validity of the Ship Survey Certificate will be temporarily suspended until the reactivation survey is completed.

Reactivation survey for laid-up vessel

The highest survey among surveys which have not been carried out during the period of laying-up shall be completed for releasing laying-up. If Special Survey (Renewal survey) is to be done, the validity of Ship Survey Certificate is to be valid from its completion date. (Presidential Decree of Ship Safety Act, Article 5, para.3-4 Grace period of survey)The grace period of survey resulting from ship's laying-up is maximum of 2 years. However, the notice of ship's laying-up shall be attained for the certain period decided within 1 year taking into consideration that the periodical surveys are carried out annually.

Reporting and management of uninspected vessels (overdue, withdraw, suspension)

Refer to the attached file “A6.9 Guidelines for Preventing Uninspected Vessels and Imposing Fines (Korean)” provided by the Administration regarding management of uninspected vessels and reporting contents.

Ship Equipment Inspection for Ship Use of Approved Type and Preparatory Inspection of Articles for Ship Use

(Note: “Ship Equipment for Ship Use” and “Articles for Ship Use” have the same meaning)

Ship Equipment Inspection for Ship Use of Approved Type

(Refer to the “Standards for type approval test and inspection of articles for ship use” by the Announcement of Ministry of Oceans and Fisheries (MOF)).

Method of ship equipment inspection

Confirmation of drawings and specification approved by type approval test.

Random samples should be done by the Surveyor. The number of the samples is in accordance with the number of applied inspection and annexed Table 2 of the “Standard for type approval test and inspection of articles for ship use”.

Ship equipment inspection items and sample test method are in accordance with Table 2 Inspection Item and Table 3 Sampling Method in “Standard for type approval test and inspection of articles for ship use”.

The test items which cannot be carried out at the venue of manufacture or work place of the applicant should be requested to be tested at the appointed and announced type approval test organization. The period needed for the tests, inter alia, is excluded from the regulatory handling period.

The test result that is issued after being requested to the type approval test organization mentioned above, and carried out at the same test organization, may be regarded as acceptable even when the Surveyor does not attend the test.

Completion of ship equipment inspection and issued certificate.

The articles for ship use which have passed ship equipment inspection should be punched or pressure sealed with the inspection punch mark (hereafter called “Recognised Organisation (RO)”) of Annex table 18 of Enforcement Decree of Ship Safety Act.Certificate should be issued with the SS-Form 47 Certificate of Ship Equipment Inspection for Ship Use of Approved Type (see SS-Form 47 _ Certificate of Ship Equipment Inspection for Ship Use of Approved Type).

Guidance on Preparatory Inspection of Articles for Ship Use

Purpose of the guidance

The purpose of the guidance is to specify the necessary items to carry out preparatory inspection of articles for ship use (hereinafter called "preparatory inspection") in accordance with the requirements in Article 54 of the Enforcement Decree of Ship Safety Act.

Items to be inspected

Items to be inspected are the articles for ship use of life-saving appliances, fire fighting appliances, accommodations and navigational equipment specified in Annex Table 1 of the Standard and Items for Preparatory Inspection of Articles for Ship Use (Announcement of MOF No. 2019-136).

Venue of preparatory inspection

The venue of preparatory inspection is the manufacturing work or service station of the concerned articles. However, the inspection may be carried out at the venue where facilities necessary for the inspection are available, if some inspection items are not possible at the work place.

Standards of preparatory inspection

Standards of preparatory inspection, in accordance with inspection items, are the standards specified by the Announcement of the Ministry of Oceans and Fisheries due to Article 26 of the Ship Safety Act for the ship's equipment by Article 4 of the Enforcement Decree of Ship Safety Act.

However, KS(Korean Standard), ISO or SOLAS is applied for the following cases:

  1. if it is stipulated in the Standard for Ship's Equipment in accordance with Article 26 of the Ship Safety Act, but not in the Standard for type approval test and inspection of articles for ship use,

  2. if the Conventions are adopted and effective,

  3. if the Conventions are adopted and effective, but not yet established in the domestic standards.

When the applied items of preparatory inspections are subject to the Standard for type approval test and inspection of articles for ship use, the type approval test standards are to be applied instead of the above standards.

Preparation of preparatory inspection

Preparatory inspections specified in Annex Table 26 of the Enforcement Decree of Ship Safety Act are to be prepared as follows:

  1. Life-saving appliance, fire-fighting appliances, accommodations: preparation for material test, pressure test and effectiveness test.

  2. Navigational equipment: preparation for effectiveness test.

If articles for ship use to be subject to preparatory inspection are the items of type approval and have been passed more than twice a year in the environmental test by type approval test organization in the last two years before the inspection application, the environmental test for the concerned articles are exempted.

Sampling

The applied inspection articles should be sampled randomly by the Surveyor and the sampling number and acceptance criteria are given in .

Inspection quantitySampling quantityAcceptance criteria
1st2nd
1 ~ 2020% of total20% of total
  • When all of the 1st samples pass, inspected items pass.

  • When more than one (1) sample among the 1st samples fail, result is failed, and when only one sample fails, the second samples should be inspected.

  • When all of the second samples pass, inspected items are regarded to have passed.

21 ~ 5018% of total18% of total
51 ~ 10015% of total15% of total
101 ~ 50010% of total10% of total
More than 5015% of total5% of total
Report and certificate

On the inspection column on name plate which is fitted on each passed article for ship use, inspection mark (Recognised Organisation (RO)) is to be engraved or sealed, as specified in Annex Table 25 of the Enforcement Decree of Ship Safety Act. However, for materials which are difficult to be engraved it is to be marked with not rubbed out ink, as appropriate.The certificate of Articles for Ship Use is to be issued with Form No.56 annexed to the Enforcement Decree of Ship Safety Act (see SS-Form 56 _ Certificate of Articles for Ship Use)

Omission of inspection

(Article 2.2 of the Standard and Items for Preparatory Inspection of Articles for Ship Use (Announcement of MOF No. 2019-136, 2019.8.13)) Preparatory inspection of one of the following articles for ship use which has been inspected by the Authority, party itself of SOLAS (called "foreign authority" hereafter) or by the classification society recognized by MOF is waived:

  1. articles for ship use onboard the ship which was constructed or repaired in foreign county,

  2. articles for ship use onboard the ship which was imported or chartered,

  3. articles for ship use which were not manufactured domestically.

Preparatory inspections shall not be carried out on articles for ships that have been installed and inspected on other existing ships.

Appendix — Agreement governing the delegation of statutory certification services of ships

Agreement

See the attached file “Agreement between MOF & Recognised Organisation (RO) on 21 June 2023.pdf”.

The National Legislations that are pertinent to this Agreement are as follows:

  • Article 60, Ship Safety Act

  • Article 112, Marine Environment Management Act

  • Article 48, Marine Safety Act

  • Article 38, International Ship and Port Facility Security Act

  • Article 29-2, Ship Act

  • Article 30, Ballast Water Management Act

Appendix 1 to the Agreement

Applicable Instruments and Degree of Authorisation

See the attached file “Appendix 1 to Agreement between MOF & Recognised Organisation (RO) on 21 June 2023.pdf”.

Appendix 2 to the Agreement

Reporting to the Administration

See the attached file “Appendix 2 to Agreement between MOF & Recognised Organisation (RO) on 21 June 2023.pdf”.

Refer to the attached file “A6.10 Report to the Korean government”, which contains information on preparation of report materials, recipients of the report, reporting time, and basis for the report contents.

Appendix — AGREEMENT GOVERNING THE DELEGATION FOR THE APPROVAL OF MARINE POLLUTION PREVENTION PLAN OF SHIP (SOPEP AND SMPEP).

Agreement (Korean only)

See the attached file “Agreement for the approval of MPP Plan_31 December 2019”.

See the attached file “Notification of extension of MPP approval agreement period_ Until 31 December 2029”

The National Legislations that are pertinent to this Agreement are as follows:

  • Article 31, Marine Environmental Management Act

  • Article 112, Marine Environmental Management Act

  • Article 37, Annex I of MARPOL and Article 17, Annex II of MARPOL

Guidance for approval of MPP plan to ships registered in the Republic of Korea

See attached “Guidance for approval of MPP plan.pdf”, including approval fee scale suggested by KCG

Appendix — CERTIFICATE OF SHIP’S BALLAST WATER MANAGEMENT SYSTEM TYPE APPROVAL TESTING LABORATORY.

Certificate

See the attached file “Certificate of Readiness Evaluation to BWMS.pdf”.

The national/international Legislations that are pertinent to this agreement are as follows:

  • Article 19.2, Ballast Water Management Act.

  • Article 36.2, Enforcement decree of Ballast Water management Act.

  • Guidelines for Approval of Ballast Water Management System (G8) _ Readiness Evaluation.

Term of certificate

Term of certificate: from 18th April 2018 unrestricted.

Guidance for Readiness Evaluation to BWTS to ships registered in the Republic of Korea

See attached “Guidance for Readiness Evaluation to BWTS_Rev 2”.

Appendix — REFERENCE DOCUMENTS

Reference data for the inspection of Korean Ships (Korean)

Refer to attached file “Reference data for the inspection of Korean Ships_Rev.9”

Type of Vessel _ Ship Survey Certificate (Korean & English)

Refer to attached file “A6.2 Type of vessel _ Ship Survey Certificate_2025”

Korean law relating to ship survey (Korean)

Refer to attached file “Korean law relating to ship survey_Rev 3”

Tables for Inventory and Spare parts for Machinery

Refer to attached file “Tables for inventory and Spare parts for Machinery”

BWM and IOPP DE _ Harmonization _ MOF _ KOREA

Refer to attached file “BWM and IOPP DE_Harmonization _MOF_ KOREA”

Accreditation procedure for Hull Thickness Measurement Company in outside of Korea

Refer to attached file “Accreditation procedure for Hull Thickness Measurement Company in outside of Korea”.

Guidelines for Ship Survey by Remote Method (Korean & English)

Refer to attached file “Guidelines for Ship Survey by Remote Method MOF Notice_MITD-607_2026_03_09”.

Temporary guidance regarding unavailability of New EPIRB - MSC 471(101) (English)

Refer to attached file “Temporary acceptance of EPIRB in compliance with existing IMO Resolution A.810(19)_MOF”.

Guidelines for preventing uninspected vessels and imposing fines

Refer to attached files in Korean “A6.9 Guidelines for Preventing Uninspected Vessels and Imposing Fines (Korean)”, “A6.9 Attachment 1” and “A6.9 Attachment 2”.

Report to the Korean Government

Refer to attached excel file in Korean and English “A6.10 Report to the Korean government”.

Ship accident record

Refer to attached excel file in Korean and English “A6.11 Ship accident record”.

Appendix — REFERENCE FORMS _ CERTIFICATES

SS-Form 3 _ Ship-Building Survey Certificate

Refer to attached file “SS-Form 3.docx”

SS-Form 7 _ Application for postponement of intermediate surveys

Refer to attached file “SS-Form 7.docx”

SS-Form 9 _ Temporary Navigation Certificate

Refer to attached file “SS-Form 9_Rev 2024.docx”

Temporary Navigation Survey Report

Refer to attached file “Temporary Navigation Survey Report_Rev1_2024”

Checklist Towing Survey

Refer to attached file “Checklist Towing Survey”

SS-Form 47 _ Certificate of Ship Equipment Inspection for Ship Use of Approved Type

Refer to attached file “SS-Form 47 Certificate of Ship Equipment Inspection for Ship Use of Approved Type”

SS-Form 56 _ Certificate of Articles for Ship Use

Refer to attached file “SS-Form 56 Certificate of Articles for Ship Use”

BW-Form 17 _ Certificate of Inspection on Ballast Water Management System

Refer to attached file “BW-Form 17 Certificate of Inspection on Ballast Water Management System_20240229”

BW-Form 17-1 _ Ballast Water Management System Inspection Report_2021 July

Refer to attached file “BW-Form 17-1 Ballast Water Management System Inspection Report_ 2021 July”

BW-MOF-1 _ Inspection Report for Ballast Water Management System

Refer to attached file “BW-MOF-1 BWMS Inspection report”

SS-MOF-1 _ Statement of the Cause of laying-up

Refer to attached file “SS-MOF-1 Statement for the Cause of Laying”

KOR-RFS-01 _ Request for survey Korean flag vessel and BBC-HP

Refer to attached file “KOR-RFS-01 Request for survey Korean Flag Vessel and BBC-HP”

Application and Declaration of BWM Convention Electronic Record Book

Refer to attached file “A7.13 Application and Declaration of BWM Convention Electronic Record”

Appendix — Specific Certificates: National and bilingual International certificates.

List of National certificates

- SS-Form 5 - Ship survey certificate less than 12m

- SS-Form 6 - Ship survey certificate above than 12m

- PP-Form 9 - Marine Prevention Pollution Certificate and Supplement PP-Form 10

- PP-Form 17 - Temporary Marine Prevention Pollution Certificate

- SS-Form 8 - Temporary Alteration Certificate

- SS-Form 76 - Towing certificate

- SS-Form 15 - Nuclear Cargo Ship Safety Certificate

- SS-Form 11 - Nuclear Passenger Ship Safety Certificate

- SS-Form 25 - Fitness Certificate for Carriage of INF Cargo

International Certificates

International Certificates must be bilingual Korean/English